YASKAWA GA700 Technical Manual page 457

Setting Function
3C LOCAL/REMOTE
Status
3D During Speed
Search
3E PID Feedback Low
3F PID Feedback
High
4A During KEB Ride-
Thru
4B During Short
Circuit Braking
4C During Fast Stop
4D oH Pre-Alarm
Time Limit
4E Braking Transistor
Fault (rr)
4F Braking Resistor
Overheat (oH)
60 Internal Cooling
Fan Alarm
61 RotorPosition
Detection
Complete
62 MEMOBUS
Register 1 (H2-
07&H2-08)
63 MEMOBUS
Register 2 (H2-
09&H2-10)
65 Standby output
66 Comparator1
67 Comparator2
69 External Power
24V Supply
YASKAWA ELECTRIC SIEP C710617 01B YASKAWA AC Drive GA700 Technical Manual
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the Run command source or frequency reference source is
LOCAL.
ON : LOCAL
OFF : REMOTE
V/f CL-V/f OLV CLV AOLV
The terminal turns on when speed search is executing.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when FbL [PID Feedback Loss] is detected.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when FbH [Excessive PID Feedback] is detected.
V/f CL-V/f OLV CLV AOLV
The terminal turns on while the KEB Ride-Thru function is being executed.
V/f CL-V/f OLV CLV AOLV
The terminal turns on during Short Circuit Braking.
Note:
This function is enabled only when using PM motors while A1-02 = 8 [Control
Method Selection = EZ Open Loop Vector Control].
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the fast stop is active.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when L8-03 = 4 [Overheat Pre-Alarm Ope Selection = Run@L8-
19 Rate] and oH [Heatsink Overheat] does not clear even after the drive diminishes the
frequency for 10 cycles.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the braking transistor integrated into the drive overheats and
rr [Dynamic Braking Transistor] is detected.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the braking resistor overheats and rH [Braking Resistor
Overheat] is detected.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when a failure is detected in the cooling fan inside the drive.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the Run command is input into the drive and the drive detects
the motor magnetic pole position of the PM motor.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the bit specified by H2-07 turns on regarding the
MEMOBUS register address configured with H2-08.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when the bit specified by H2-10 turns on regarding the
MEMOBUS register address configured with H2-09.
V/f CL-V/f OLV CLV AOLV
The terminal turns off after the drive stops operating and the time set with b8-51
[Standby Mode Wait Time] elapses.
ON : The Run command turns on and the magnetic contactor on the input side turns off.
OFF : The Run command turns off and the drive stops operating. Then, the magnetic
contactor on the input side turns off after the time set with b8-51 [Standby Mode Wait
Time] elapses.
V/f CL-V/f OLV CLV AOLV
The monitor value configured with H2-20 is on while within range of the time configured
with H2-24 and the values of H2-21 and H2-22 are within range.
V/f CL-V/f OLV CLV AOLV
The monitor value configured with H2-26 is on while within range of the time configured
with H2-30 and the values of H2-27 and H2-28 are within range.
V/f CL-V/f OLV CLV AOLV
The terminal turns on when an external 24V power supply is provided between terminal
PS-AC.
ON : Power is supplied by an external 24V power supply.
OFF : Power is not supplied by an external 24V power supply.
Description
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
10.10 H: Terminal Functions
Ref.
796
797
797
797
797
797
797
798
798
798
798
798
798
798
798
799
799
800
10
457