YASKAWA GA700 Technical Manual page 406

10.5 b: Application
No.
Name
(Hex.)
b5-12 Feedback Loss
Detection Select
(01B0)
b5-13 PID Feedback Loss
Detection Lvl
(01B1)
b5-14 PID Feedback Loss
Detection Time
(01B2)
b5-15 PID Sleep Function
Start Level
(01B3)
b5-16 PID Sleep Delay
Time
(01B4)
b5-17 PID Accel/Decel
Time
(01B5)
b5-18 PID Setpoint
Selection
(01DC)
b5-19 PID Setpoint Value
(01DD)
RUN
b5-20 PID Setpoint
Scaling
(01E2)
b5-34 PID Output Lower
Limit
(019F)
RUN
b5-35 PID Input Limit
(01A0)
RUN
b5-36 PID Feedback
High Detection Lvl Sets the level that triggers Excessive PID Feedback [FbH] as a
(01A1)
b5-37 PID Feedback
High Detection
(01A2)
Time
b5-38 PID Setpoint User
Display
(01FE)
b5-39 PID Setpoint
Display Digits
(01FF)
406
Description
V/f CL-V/f OLV CLV AOLV
Enables or disables PID feedback loss detection. Sets operation after
the drive detects PID feedback loss.
0 : No alarm_Always detected_DO only
1 : Alarm_Always detected
2 : Fault_Always detected
3 : No alarm_only @ PID enbl_DO only
4 : Alarm_only detected @ PID Enbl
5 : Fault_only detected @ PID Enbl
V/f CL-V/f OLV CLV AOLV
Sets the level that triggers PID Feedback Loss [FbL] as a
percentage of the maximum output frequency.
V/f CL-V/f OLV CLV AOLV
Sets the time that the PID feedback has to fall below b5-13 [PID
Feedback Loss Detection Lvl] before PID Feedback Loss [FbL] is
detected.
V/f CL-V/f OLV CLV AOLV
Sets the output level that triggers the PID Sleep function.
V/f CL-V/f OLV CLV AOLV
Sets a delay time to activate or deactivate the PID Sleep function.
V/f CL-V/f OLV CLV AOLV
Raises or lowers the PID setpoint using the acceleration and
deceleration times set to the drive. This is a soft-starter for the PID
setpoint.
V/f CL-V/f OLV CLV AOLV
Enables or disables b5-19 [PID Setpoint Value].
0 : Disabled
1 : Enabled
V/f CL-V/f OLV CLV AOLV
This setting is the PID setpoint when b5-18 = 1 [PID Setpoint
Selection = Enabled].
V/f CL-V/f OLV CLV AOLV
Determines the units used to set and display b5-19 [PID Setpoint
Value].
V/f CL-V/f OLV CLV AOLV
Sets the output lower limit for the PID control as a percentage of
E1-04 [Maximum Output Frequency].
V/f CL-V/f OLV CLV AOLV
Sets the input upper limit for the PID control as a percentage of E1-
04 [Maximum Output Frequency].
V/f CL-V/f OLV CLV AOLV
percentage of E1-04 [Maximum Output Frequency].
V/f CL-V/f OLV CLV AOLV
Sets the time that triggers Excessive PID Feedback [FbH] when the
feedback signal rises above the level set in b5-36 [PID Feedback
High Detection Lvl].
V/f CL-V/f OLV CLV AOLV
Determines the value for setting and displaying U5-01, U5-04 when
outputting the maximum output frequency.
V/f CL-V/f OLV CLV AOLV
Sets the number of digits for setting and displaying the PID setpoint.
0 : No decimal places 1
1 : One decimal place
2 : Two decimal places
3 : Three decimal places
YASKAWA ELECTRIC SIEP C710617 01B YASKAWA AC Drive GA700 Technical Manual
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM OLV/PM AOLV/PM CLV/PM EZOLV
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
OLV/PM AOLV/PM CLV/PM EZOLV OLV/PM
Default
Ref.
(Range)
0 626
(0 - 5)
0% 627
(0 - 100%)
1.0 s 627
(0.0 - 25.5 s)
Determined by A1- 627
02
(0.0 - 590.0)
0.0 s 627
(0.0 - 25.5 s)
0.0 s 627
(0.0 - 6000.0 s)
0 627
(0, 1)
0.00% 628
(0.00 - 100.00%)
1 628
(0 - 3)
0.0% 628
(-100.0 - +100.0%)
1000.0% 628
(0.0 - 1000.0%)
100% 629
(0 - 100%)
1.0 s 629
(0.0 - 25.5 s)
Determined by b5- 629
20
(1 - 60000)
Determined by b5- 629
20
(0 - 3)