YASKAWA GA700 Technical Manual page 395

Parameters
U5 PID Monitors
U6 Operation Status Monitors
◆
List of Parameters Enabled in Expert Mode
No.
A1-11 Firmware update lock
b1-21 CLV Start Selection
b1-35 Multi-Function DI dead band time
b3-06 Speed Estimation Current Level 1
b3-07 Speed Estimation Current Level 2
b3-08 Speed Estimation ACR P Gain
b3-09 Speed Estimation ACR I Time
b3-10 Speed Estimation Detection Gain
b3-17 Speed Est. Retry Current Level
b3-18 Speed Est. Retry Detection Time
b3-25 Speed Search Wait Time
b3-26 Direction Determining Level
b3-27 Start Speed Search Select
b3-29 Speed Search Back-EMF Threshold
b3-31 Search current Level 1
b3-32 Search current Level 2
b3-33 Spd Search during UV Selection
b3-35 Voltage Detection Low Level
b3-36 Wait Restart Level
b3-55 Current Increment Time
b4-03 H2-01 ON Delay Time
b4-04 H2-01 OFF Delay Time
b4-05 H2-02 ON Delay Time
b4-06 H2-02 OFF Delay Time
b4-07 H2-03 ON Delay Time
b4-08 H2-03 OFF Delay Time
b4-09 H2-04 ON Delay Time
b4-10 H2-04 OFF Delay Time
b5-08 PID Primary Delay Time Constant
b8-02 Energy Saving Gain
b8-03 Energy Saving Filter Time
b8-04 Energy Saving Coefficient Value
b8-05 Power Detection Filter Time
b8-06 Search Operation Voltage Limit
b8-16 PM E-Save Coefficient Ki
b8-17 PM E-Save Coefficient Kt
b8-18 E-Save d-axis Current FilterTime
YASKAWA ELECTRIC SIEP C710617 01B YASKAWA AC Drive GA700 Technical Manual
Name
Table 10.1 Parameters Enabled in Expert Mode
Name
Parameters
U8 DriveWorksEZ Monitors
No.
b8-19 E-Save Search Injection Freq
b8-20 PM E-Save Search Width
b8-21 PM E-Save Search Gain
b8-22 PM E-Save Search LPF Cutoff Freq
b8-23 PM E-Save Search Limit
b8-24 PM E-Save High Freq ACR Gain
b8-25 PM E-Save Search Start level
b8-26 PM E-Save Power Setpoint
b8-28 Save Energy Priority Function
C3-16 Vout Modulation Limit Start Lvl
C3-17 Vout Modulation Limit Max Level
C3-18 Output Voltage Limit Level
C3-28 Adaptive Slip Contrl Mode Select
C4-19 T-ripple suppress freq
C4-20 vol compensation adjust 1
C4-21 vol compensation adjust 2
C5-17 Motor Inertia
C5-18 Load Inertia Ratio
C5-29 Speed Control Response
C5-37 Motor 2 Inertia
C5-38 Motor 2 Load Inertia Ratio
C5-50 Notch Filter Frequency
C5-51 Notch Filter Bandwidth
E1-11 Mid Point B Frequency
E1-12 Mid Point B Voltage
E1-13 Base Voltage
E2-09 Motor Mechanical Loss
E3-11 Motor 2 Mid Point B Frequency
E3-12 Motor 2 Mid Point B Voltage
E3-13 Motor 2 Base Voltage
E4-09 Motor 2 Mechanical Loss
E5-25 Polarity Estimation Reversal
F3-10 Terminal D0 Function Selection
F3-11 Terminal D1 Function Selection
F3-12 Terminal D2 Function Selection
F3-13 Terminal D3 Function Selection
F3-14 Terminal D4 Function Selection
10.3 Parameter Groups
Name
Name
395
10