Gpio Low Power Mode Wakeup Select 1 (Gpiolpmsel1) Register; Gpio Low Power Mode Wakeup Select 2 (Gpiolpmsel2) Register; Gpio Low Power Mode Wakeup Select 1 (Gpiolpmsel1) Register Field Descriptions; Gpio Low Power Mode Wakeup Select 2 (Gpiolpmsel2) Register Field Descriptions - Texas Instruments Concerto F28M36 Series Technical Reference Manual

Table of Contents

Advertisement

www.ti.com
Figure 4-94. GPIO Low Power Mode Wakeup Select 1 (GPIOLPMSEL1) Register
31
30
GPIO31
GPIO30
R/W-0
R/W-0
23
22
GPIO23
GPIO22
R/W-0
R/W-0
15
14
GPIO15
GPIO14
R/W-0
R/W-0
7
6
GPIO7
GPIO6
R/W-0
R/W-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 4-118. GPIO Low Power Mode Wakeup Select 1 (GPIOLPMSEL1) Register Field Descriptions
Bits
Field
31-0
GPIO31 - GPIO0
(1)
This register is EALLOW protected.

4.2.7.54 GPIO Low Power Mode Wakeup Select 2 (GPIOLPMSEL2) Register

The GPIO Low Power Mode Wakeup Select 2 (GPIOLPMSEL2) register is shown and described in the
figure and table below.
Figure 4-95. GPIO Low Power Mode Wakeup Select 2 (GPIOLPMSEL2) Register
31
30
GPIO63
GPIO62
R/W-0
R/W-0
23
22
GPIO55
GPIO54
R/W-0
R/W-0
15
14
GPIO47
GPIO46
R/W-0
R/W-0
7
6
GPIO39
GPIO38
R/W-0
R/W-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Table 4-119. GPIO Low Power Mode Wakeup Select 2 (GPIOLPMSEL2) Register Field Descriptions
Bits
Field
31-0
GPIO63 - GPIO32
(1)
This register is EALLOW protected.
SPRUHE8E – October 2012 – Revised November 2019
Submit Documentation Feedback
29
28
GPIO29
GPIO28
R/W-0
R/W-0
21
20
GPIO21
GPIO20
R/W-0
R/W-0
13
12
GPIO13
GPIO12
R/W-0
R/W-0
5
4
GPIO5
GPIO4
R/W-0
R/W-0
Value
Low Power Mode Wakeup Selection 1. Each bit in this register corresponds to one GPIO
port A pin (GPIO0 - GPIO31).
0
If the bit is cleared, the signal on the corresponding pin will have no effect on the HALT and
STANDBY low power modes.
1
If the respective bit is set to 1, the signal on the corresponding pin is able to wake the
device from both HALT and STANDBY low power modes.
29
28
GPIO61
GPIO60
R/W-0
R/W-0
21
20
GPIO53
GPIO52
R/W-0
R/W-0
13
12
GPIO45
GPIO44
R/W-0
R/W-0
5
4
GPIO37
GPIO36
R/W-0
R/W-0
Value
Low Power Mode Wakeup Selection 1. Each bit in this register corresponds to one GPIO
port B pin (GPIO32 - GPIO63) .
0
If the bit is cleared, the signal on the corresponding pin will have no effect on the HALT and
STANDBY low power modes.
1
If the respective bit is set to 1, the signal on the corresponding pin is able to wake the
device from both HALT and STANDBY low power modes.
Copyright © 2012–2019, Texas Instruments Incorporated
C28 General-Purpose Input/Output (GPIO)
27
26
GPIO27
GPIO26
R/W-0
R/W-0
19
18
GPIO19
GPIO18
R/W-0
R/W-0
11
10
GPIO11
GPIO10
R/W-0
R/W-0
3
2
GPIO3
GPIO2
R/W-0
R/W-0
(1)
Description
27
26
GPIO59
GPIO58
R/W-0
R/W-0
19
18
GPIO51
GPIO50
R/W-0
R/W-0
11
10
GPIO43
GPIO42
R/W-0
R/W-0
3
2
GPIO35
GPIO34
R/W-0
R/W-0
(1)
Description
General-Purpose Input/Output (GPIO)
25
24
GPIO25
GPIO24
R/W-0
R/W-0
17
16
GPIO17
GPIO16
R/W-0
R/W-0
9
8
GPIO9
GPIO8
R/W-0
R/W-0
1
0
GPIO1
GPIO0
R/W-0
R/W-0
25
24
GPIO57
GPIO56
R/W-0
R/W-0
17
16
GPIO49
GPIO48
R/W-0
R/W-0
9
8
GPIO41
GPIO40
R/W-0
R/W-0
1
0
GPIO33
GPIO32
R/W-0
R/W-0
461

Advertisement

Table of Contents
loading

Table of Contents