Related Manuals for Texas Instruments CC1110-CC1111DK
Summary of Contents for Texas Instruments CC1110-CC1111DK
- Page 1 CC1110/CC2510 CC1110-CC1111DK CC2510-CC2511DK Development Kit User Manual Page 1 of 31 swru134a...
-
Page 2: Table Of Contents
CC1110/CC2510 Table of contents INTRODUCTION ........................3 ABOUT THIS MANUAL ......................3 DEFINITIONS..........................4 KIT CONTENT ..........................5 ...........................5 ARDWARE ® SMARTRF 04EB ........................6 USB MCU ............................7 5.1.1 Bootloader..................................... 7 5.1.2 Programming USB controller............................... 7 USB MCU ......................8 SIGNAL NAMES ® HARDWARE DESCRIPTION SMARTRF 04EB..............9 ®... -
Page 3: Introduction
® Thank you for purchasing a SmartRF 04DK Development Kit. ® Please note that Texas Instruments uses the term SmartRF 04DK as a collective term for all ® development kits on the Chipcon SmartRF 04 platform. This development platform supports ®... -
Page 4: Definitions
CC1110/CC2510 Definitions SmartRF04EB CC1110EM or CC2510EM Evaluation Board. Main board with LCD, USB CC1110/CC2510 Evaluation Module, interface, LEDs, pot-meter etc. Platform for the small plug-in module CC1110- Evaluation Modules (EM). CC1111DK/CC2510-CC2511DK, should be used as reference design for antenna and RF layout. -
Page 5: Kit Content
04EB • 2 x CC2510EM evaluation modules in the CC2510-CC2511DK • 2 x CC1110EM433 and 2 x CC1110EM868-915 evaluation modules in the CC1110-CC1111DK • Antennas for the appropriate frequency range • 1 x USB dongle • 2 x USB cables •... -
Page 6: Smartrf 04Eb
CC1110/CC2510 ® SmartRF 04EB ® This chapter includes overall information that applies to SmartRF 04EB. In the following SoC means Chipcon System on Chip, i.e. CC1110 or CC2510. Figure 1: Main components ® Figure 1 shows the main components on the SmartRF 04EB. -
Page 7: Usb Mcu
CC1110/CC2510 USB MCU 5.1.1 Bootloader The USB controller is programmed with a bootloader when it is shipped from the factory. The bootloader allows programming of new code into the USB MCU without the Silicon Labs’ ® serial adapter. The bootloader communicates with SmartRF Studio or a custom program via USB. -
Page 8: Usb Mcu Signal Names
CC1110/CC2510 USB MCU signal names The USB MCU is a C8051F320 from Silicon Labs. Please see the Silicon Labs web site for detailed information about this MCU. The following table shows the usage of I/O pins on the USB MCU. Pin name Signal name 0-ohm... -
Page 9: Hardware Description Smartrf 04Eb
CC1110/CC2510 ® Hardware description SmartRF 04EB Supply selection Power connector switch Connectors for evaluation module (EM) DC jack debug/flash connector test connectors connector USB MCU USB MCU reset debug connector USB MCU Potentio meter Head- phone RS-232 output connector Mic. input Button Joystick... -
Page 10: Powering Smart Rf ® 04Eb
CC1110/CC2510 ® Powering SmartRF 04EB ® If several power sources are connected to SmartRF 04EB, the board will be powered from the supply that supplies the highest voltage. Figure 4: Power switch setting The Power Switch S3 must be set according to what power source is used. If 3.3V is applied using the power terminal block, the switch should be set to the left position. -
Page 11: Usb Interface
Chebychev filter. This filter serves to attenuate frequencies above 6 kHz, and so converts the PWM signal to an analogue audio signal. A headphone amplifier IC (TPA4411 from Texas Instruments) is used to drive the headphones. Note that the headphone amplifier IC uses switch-mode power supply techniques to generate negative voltages, and this may cause electrical noise. -
Page 12: Spi Interface Swap Jumpers On Smartrf 04Eb
CC1110/CC2510 ® SPI interface swap jumpers on SmartRF 04EB The SPI swap jumpers at P3 shall be set according to Figure 6. Figure 6: SPI jumper setting Page 12 of 31 swru134a... -
Page 13: I/Oconnectors
CC1110/CC2510 I/O connectors The I/O connectors bring out all the signals from the EM connectors. These connectors are compatible with Agilent logic analyser probes. The connectors allow easy access to I/O signals and to connect prototyping boards. Function Function P0_0/MIC_IN P2_0 /LED4 P1_0/LED1... -
Page 14: Em Connectors
CC1110/CC2510 EM connectors ® The EM connectors are used for connecting the EM to the SmartRF 04EB. The connectors P1 and P2 are used as the main interface. The EM should be used as an RF reference design with the Chipcon SoC, decoupling, and all required RF circuitry. -
Page 15: Em Lcd Connection
CC1110/CC2510 6.10 EM LCD connection Please note that the I/O pins P2_3 and 2_4 on the SoC are connected to a 32 kHz X- oscillator on the CC1110EM and CC2510EM boards. The LCD display is therefore internally, on the EM, swapped from P1_2 to P2_3 and P2_0 to P2_4 as shown in Figure 8. Therefore there is no access to LED2 (red) and LED4 (blue) from the SoC. -
Page 16: Application Examples And Rf Testing
The CC1110/CC2510 development kit is accompanied by a Packet Error Rate (PER) software example. This together with a corresponding document can be downloaded from the Texas Instruments web site. The software example is provided as source code. It is written for the IAR Embedded Workbench for 8051. -
Page 17: Rf Testing
CC1110/CC2510 RF testing ® RF testing is best performed by using SmartRF Studio together with the Development Kit. ® Connect the SmartRF04DK to a PC using the USB interface. Start SmartRF Studio and ® select the SmartRF 04 tab. Select the correct Development Kit (several Development Kits can be connected to a PC at once), it should be listed as “CC2510 –... -
Page 18: Iar Embedded Workbench
CC1110/CC2510 IAR Embedded Workbench An evaluation version of IAR Embedded Workbench is included in the CC1110/CC2510 development kit. This chapter describes how to obtain an IAR license number, how to install the IAR evaluation version and how to obtain a license for 60 days additional evaluation. The 60 days additional evaluation time is provided to all TI Low Power Wireless development kit customers. -
Page 19: Installation From The Cd
CC1110/CC2510 The license number and license key from the “Registration confirmed” web page are required during the installation. Please note that you shall use the license number from the “Registration confirmed” web site even though the installation program states that the license number can be found on the CD cover. -
Page 20: Obtaining 60 Days Additional License
PDF format. More information is found on this web site: http://www.iar.com/p89661/p89661_eng.php#ks. Please choose the version for the 8051 processor family / core, not the version for the Texas Instruments MSP430 processor family / core. Page 20 of 31 swru134a... -
Page 21: Using Smartrf
CC1110/CC2510 ® Using SmartRF 04EB for prototyping ® SmartRF 04EB includes a debug and programming interface. The debug interface is ® controlled by 2 communication pins. On the SmartRF 04EB the interface is controlled by the USB MCU. This allows both programming and an emulator interface using the USB port. Table 1 on page 8 shows which pins on the MCU that are used for various peripheral ®... -
Page 22: System-On-Chip Debug Plug-In Board (Soc_Dem)
CC1110/CC2510 ® The pin out used on the SmartRF 04EB is explained in Table 4 and Figure 15. All signals in bold in the table are required. Figure 15 shows the required signals for a minimum connector layout. Function Note Used to set correct voltage for the voltage level converter Debug Clock (DC) -
Page 23: Programming The Soc With A Hex File
Chipcon Flash Programmer please refer to the Chipcon Flash Programmer User Manual. Figure 17: Chipcon Flash programmer software ® 11 SmartRF 04EB Troubleshooting ® Please refer to Texas Instruments Design Note, DN300 for SmartRF 04EB troubleshooting: DN300 - SmartRF04EB Troubleshooting Page 23 of 31 swru134a... -
Page 24: Smartrf04Dk Schematics
CC1110/CC2510 12 SmartRF04DK Schematics ® Figure 18: SmartRF 04EB schematic, page 1 Page 24 of 31 swru134a... - Page 25 CC1110/CC2510 ® Figure 19: SmartRF 04EB schematic, page 2 Page 25 of 31 swru134a...
- Page 26 CC1110/CC2510 ® Figure 20: SmartRF 04EB schematic, page 3 Page 26 of 31 swru134a...
- Page 27 CC1110/CC2510 ® Figure 21: SmartRF 04EB schematic, page 4 Page 27 of 31 swru134a...
- Page 28 CC1110/CC2510 ® Figure 22: SmartRF 04EB schematic, page 5 Page 28 of 31 swru134a...
- Page 29 CC1110/CC2510 ® Figure 23: SmartRF 04EB schematic, page 6 Page 29 of 31 swru134a...
- Page 30 CC1110/CC2510 ® Figure 24: SmartRF 04EB schematic, page 7 Revision Description/Changes 2.0.1 (PCB 1.9) R104 not mounted by default, see section 6.5 2.0 (PCB 1.9) Changes to production test, no physical changes to product. 1.9 (PCB 1.9) Initial public release ®...
-
Page 31: Evaluation Modules
CC1110/CC2510 13 Evaluation Modules Gerber files and full documentation for the released evaluation modules can be downloaded from the Texas Instruments web site. Figure 25: Evaluation Module 14 Document history Revision Date Description/Changes 2007-10-10 Updated information concerning the CC1110-CC1111DK. Initial release. - Page 32 TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products...