Table of Contents
Advertisement
System Control Registers
1.13.9.8 EXEONLYR Register
31
23
15
14
Reserved
R-0
7
6
EXEONLY_SECT
EXEONLY_SECT
G
H
R-0
R-0
LEGEND: R/W = Read/Write; R = Read only; -n = value after reset
Bit
Field
31-14
Reserved
13
EXEONLY-
SECTA
12
EXEONLY_SECT
B
11
EXEONLY_SECT
C
10
EXEONLY_SECT
D
9
EXEONLY_SECT
E
8
EXEONLY_SECT
F
274
System Control and Interrupts
Figure 1-160. EXEONLYR Register
13
12
EXEONLY-SECTA EXEONLY_SECTB EXEONLY_SECT
R-0
5
4
EXEONLY_SECTI EXEONLY_SECTJ EXEONLY_SECTK EXEONLY_SECTL EXEONLY_SECT
R-0
R-0
Table 1-171. EXEONLYR Register Field Description
Value
Description
Reserved
Value in this field gets loaded from EXEONLY[13:13] when a read is issued to the EXEONLY
address location in flash.
0
Execute-Only protection is enabled for C28x flash sector A.
1
Execute-Only protection is disabled for C28x flash sector A.
Value in this field gets loaded from EXEONLY[12:12] when a read is issued to the EXEONLY
address location in flash.
0
Execute-Only protection is enabled for C28x Flash Sector B (only if it is allocated to the control
subsystem)
1
Execute-Only protection is disabled for C28x Flash Sector B (only if it is allocated to the control
subsystem)
Value in this field gets loaded from EXEONLY[11:11] when a read is issued to the EXEONLY
address location in flash.
0
Execute-Only protection is enabled for C28x Flash Sector C (only if it is allocated to the control
subsystem)
1
Execute-Only protection is disabled for C28x Flash Sector C (only if it is allocated to the control
subsystem)
Value in this field gets loaded from EXEONLY[10:10] when a read is issued to the EXEONLY
address location in flash.
0
Execute-Only protection is enabled for C28x Flash Sector D (only if it is allocated to the control
subsystem)
1
Execute-Only protection is disabled for C28x Flash Sector D (only if it is allocated to the control
subsystem)
Value in this field gets loaded from EXEONLY[9:9] when a read is issued to the EXEONLY address
location in flash.
0
Execute-Only protection is enabled for C28x Flash Sector E (only if it is allocated to C28x zone1)
1
Execute-Only protection is disabled for C28x Flash Sector E (only if it is allocated to C28x zone1)
Value in this field gets loaded from EXEONLY[8:8] when a read is issued to the EXEONLY address
location in flash.
0
Execute-Only protection is enabled for C28x Flash Sector F (only if it is allocated to the control
subsystem)
1
Execute-Only protection is disabled for C28x Flash Sector F (only if it is allocated to the control
subsystem)
Copyright © 2012–2019, Texas Instruments Incorporated
Reserved
R-0
Reserved
R-0
11
10
EXEONLY_SECT
C
D
R-0
R-0
3
2
R-0
R-0
SPRUHE8E – October 2012 – Revised November 2019
www.ti.com
24
16
9
8
EXEONLY_SECTE EXEONLY_SECTF
R-0
R-0
1
0
EXEONLY_SECT
M
N
R-0
R-0
Submit Documentation Feedback
Advertisement
Chapters
Table of Contents
