Canon imageRUNNER ADVANCE 6075 Series Service Manual page 770

Color Image Reader-C1
SR23 SR22 SR4
PCB3
SR5
PCB4 SR16
SR15
ACC Jam
Type Sensor Name / Description
ID Code
01 0001 DELAY Post-separation sensor 1/2/3
01 0002 STNRY Post-separation sensor 1/2/3
01 0003 DELAY Delay detection sensor
01 0004 STNRY Delay detection sensor
01 0005 DELAY Registration sensor
01 0006 STNRY Registration sensor
01 0007 DELAY Lead sensor 1
01 0008 STNRY Lead sensor 1
01 0009 DELAY Lead sensor 2
01 0010 STNRY Lead sensor 2
01 0011 DELAY Delivery sensor
01 0012 STNRY Delivery sensor
01 0013 DELAY *3 Reversal sensor
01 0014 STNRY *3 Reversal sensor
01 0042 STNRY Post-separation sensor 3
01 0043 DELAY Delay detection sensor
01 0044 STNRY Delay detection sensor
01 0045 DELAY Registration sensor
01 0046 STNRY Registration sensor
7
Error Code > Jam Code > Color Image Reader-C1
SR10
SR12 SR2
PCB2
LED
SR3
PCB5
F-7-3
Sensor ID
PCB2
PCB2
SR4
SR4
PCB3
PCB3
PCB4
PCB4
SR5
SR5
PCB5
PCB5
SR23
SR23
PCB2
SR4
SR4
PCB3
PCB3
7 Error Code > Jam Code > Color Image Reader-C1
ACC Jam
Type Sensor Name / Description
ID Code
01 0047 DELAY Lead sensor 1
01 0048 STNRY Lead sensor 1
01 0049 DELAY Lead sensor 2
01 0050 STNRY Lead sensor 2
01 0051 DELAY Delivery sensor
01 0052 STNRY Delivery sensor
*3
01 0053 DELAY Reversal sensor
01 0054 STNRY *3 Reversal sensor
01 0071 Timing NG
01 0073 Hp NG Disengaging HP sensor 1
01 0074 Hp NG Disengaging HP sensor 2
01 0075 Hp NG Pickup roller unit lifter HP sensor
01 0090 ADF OP DADF open/closed sensor 1/2
01 0091 ADF OP DADF open/closed sensor 1/2
01 0092 COVER OP Cover open/closed sensor
01 0093 COVER OP Cover open/closed sensor
01 0094 Power ON All feed type sensor
01 0095 PICKUP NG Post-separation sensor 1/2/3
*1 The state is recovered by opening and closing the Door, or turning OFF and then ON the
power supply.
If the same jam is detected although the above operation is performed, an error code will
be notified.
*2 The state is recovered by opening and closing the Door, or turning OFF and then ON the
power supply.
If it is not recovered by the above operation, it is considered an error near the target sensor.
Disconnect and then connect the connectors around the target sensor, check if the cable is
open circuit, and replace the sensor.
*3 Color Image Reader-C1 only
*4 Confirm the following sensors from service mode.
Leading Edge Position Sensor (SR22): COPIER> IO> FEEDER> P003> 2 (1: Paper
presence)
Delivery Sensor (PCB5): COPIER> IO> FEEDER> P004> 0 (0: Paper presence)
Read Sensor 2 (SR5): COPIER> IO> FEEDER> P004> 1 (0: Paper presence)
Read Sensor 1 (PCB4): COPIER> IO> FEEDER> P004> 2 (0: Paper presence)
Registration Sensor (PCB3): COPIER> IO> FEEDER> P004> 3 (0: Paper presence)
Delay sensor (SR4): COPIER> IO> FEEDER> P004> 6 (0: Paper presence)
Post-separation Sensor 3 (PCB2): COPIER> IO> FEEDER> P004> 7 (0: Paper presence)
7-85
Sensor ID
PCB4
PCB4
SR5
SR5
PCB5
PCB5
SR23
SR23
- Timing NG
SR15
SR16
SR12
SR1/3 (Reader)
SR1/3 (Reader)
SR10
SR10
*4 Power ON
SR2, SR3, PCB2
T-7-17
7-85