Canon imageRUNNER ADVANCE 6075 Series Service Manual page 699

E Detail
Location Item
Code Code
E102 -0001 -05 Title EEPROM writing error
Remedy 1. Check if the door is opened. Close the door.
2. Check the connector connection, open circuit, and the
caught cable of the DC Controller PCB (PCB1) and the
Laser Driver PCB (PCB35).
DC Controller side: J471, J472, Laser Driver side: J5100,
J5101, Relay Harness connection to Polygon Motor (M44)
and BD Sensor: J3011
3. Replace the Laser Scanner Unit.
4. Replace the Laser Driver PCB (PCB35).
5. Replace the DC Controller PCB (PCB1).
Description Failed to write to EEPROM (Power is not supplied/EEPROM
failure).
E103 -0001 -05 Title Different Laser Scanner Unit model error
Remedy Replace the Laser Scanner Unit with the one for the correct
model.
Description The scanner for 6075/6065/6055 models was installed to the
imageRUNNER ADVANCE 8105/8095/8085 models, and vice
versa.
E110 -11xx -05 Title Polygon Motor FG unlock error
Remedy 1. Check if the door is opened. Close the door.
2. Check the connector connection, open circuit, and the
caught cable of the DC Controller PCB (PCB1) and the
Laser Driver PCB (PCB35).
DC Controller side: J471, J472, Laser Driver side: J5100,
J5101, Relay Harness connection to Polygon Motor (M44)
and BD Sensor: J3011
3. Replace the Laser Scanner Unit.
4. Replace the Laser Driver PCB (PCB35).
5. Replace the DC Controller PCB (PCB1).
Description Locked state was not detected within the specified period of
time at start-up. (Power is not supplied/Polygon Motor signal
error)
7
Error Code > Error Code > Error Code Details > E100 to E197
Description
7 Error Code > Error Code > Error Code Details > E100 to E197
E Detail
Location Item
Code Code
E110 -12xx -05 Title Polygon Motor FG unlock error
Remedy 1. Check if the door is opened. Close the door.
2. Check the connector connection, open circuit, and the
caught cable of the DC Controller PCB (PCB1) and the
Laser Driver PCB (PCB35).
DC Controller side: J471, J472, Laser Driver side: J5100,
J5101, Relay Harness connection to Polygon Motor (M44)
and BD Sensor: J3011
3. Replace the Laser Scanner Unit.
4. Replace the Laser Driver PCB (PCB35).
5. Replace the DC Controller PCB (PCB1).
Description After the BD range was specified, lock was unlocked for 1
second or longer. (Power is not supplied/Polygon Motor signal
error)
E110 -13xx -05 Title Polygon Motor FG unlock error
Remedy 1. Check if the door is opened. Close the door.
2. Check the connector connection, open circuit, and the
caught cable of the DC Controller PCB (PCB1) and the
Laser Driver PCB (PCB35).
DC Controller side: J471, J472, Laser Driver side: J5100,
J5101, Relay Harness connection to Polygon Motor (M44)
and BD Sensor: J3011
3. Replace the Laser Scanner Unit.
4. Replace the Laser Driver PCB (PCB35).
5. Replace the DC Controller PCB (PCB1).
Description During the Polygon speed change, lock was unlocked for 1
second or longer. (Power is not supplied/Polygon Motor signal
error)
E110 -FFFF -05 Title Polygon Motor FG unlock error
Remedy 1. Check if the door is opened. Close the door.
2. Check the connector connection, open circuit, and the
caught cable of the DC Controller PCB (PCB1) and the
Laser Driver PCB (PCB35).
DC Controller side: J471, J472, Laser Driver side: J5100,
J5101, Relay Harness connection to Polygon Motor (M44)
and BD Sensor: J3011
3. Replace the Laser Scanner Unit.
4. Replace the Laser Driver PCB (PCB35).
5. Replace the DC Controller PCB (PCB1).
Description Failed to get the Detailed Code (communication error, power
supply error, PCB failure).
7-14
Description
7-14