Function; Install - Canon imageRUNNER ADVANCE 6075 Series Service Manual

FUNCTION

■ INSTALL

COPIER > FUNCTION > INSTALL
TONER-S Toner supply to Developing Assembly
Lv.1 Details To execute a series of operation necessary for supplying toner to
the Developing Assembly/Toner Supply area (drive the Developing
Cylinder, Toner Stirring/Feed Member, Photosensitive Drum and
ETB, and output developing bias) as a whole.
After counting down from 600 seconds., it is stopped automatically.
Use case - At installation
- When replacing the Developing Assembly
- When replacing toner in the Developing Assembly
Adj/set/operate method 1) Select the items.
"Check the Developer" is displayed.
2) Check connection, and then press OK key.
It automatically stops after 10 minutes.
Caution - Although "Check the Developer" is displayed when selecting the
item, be sure to check the connection between the Developing
Assembly and connector.
- The operation can stop manually with OK key when a failure
occurs.
Display/adj/set range During operation: xxx second (remaining time), When operation
finished normally: END
Default value 600
Required time 18 minutes
STRD-POS Scan position auto adj in DADF mode
Lv.1 Details To adjust the DADF scanning position automatically.
Use case At DADF installation/uninstallation
Adj/set/operate method 1) Set a paper for stream reading position adjustment, and then
close the DADF.
2) Select the item, and then press OK key.
The operation automatically stops after the adjustment.
3) Write the value displayed by COPIER>ADJUST>ADJ-XY>STRD-
POS in the service label.
Caution Write the adjusted value in the service label.
Display/adj/set range At normal termination: OK, At abnormal termination: NG
Required time Approx. 10 seconds
Related service mode COPIER> ADJUST> ADJ-XY> STRD-POS
Supplement/memo For the details of paper for stream reading position adjustment, refer
to the Service Manual.
8
Service Mode > COPIER > FUNCTION > INSTALL
8 Service Mode > COPIER > FUNCTION > INSTALL
COPIER > FUNCTION > INSTALL
CARD Card number setting
Lv.1 Details To set the card number to be used for Card Reader.
A series of numbers from the entered number to the number of cards
specified by CARD-RNG can be used.
Use case - At installation of the Card Reader
- After replacement of the HDD
Adj/set/operate method 1) Enter the number, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution The card management information (department ID and password) is
initialized.
Display/adj/set range 1 to 2001
Default value 1
Related service mode COPIER> OPTION> FNC-SW> CARD-RNG (Level 2)
E-RDS Set use/no use of Embedded-RDS function
Lv.1 Details To set whether to use the Embedded-RDS function.
Use case When using Embedded-RDS
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to use E-RDS, RGW-PORT, COM-TEST, COM-LOG and
RGW-ADR as a set.
Display/adj/set range 0: Not used, 1: Used (All the counter information is sent.)
Default value 0
Related service mode COPIER> FUNCTION> INSTALL> RGW-PORT, COM-TEST, COM-
LOG, RGW-ADR
Supplement/memo Embedded-RDS: Function to send device information such as the
device counter, failure, and consumables to the sales company's
server via SOAP protocol
RGW-PORT Set port number of Sales Co's server
Lv.1 Details To set the port number of the sales company's server to be used for
Embedded-RDS.
Use case When using Embedded-RDS
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to use E-RDS, RGW-PORT, COM-TEST, COM-LOG and
RGW-ADR as a set.
Display/adj/set range 1 to 65535
Default value 443
Related service mode COPIER> FUNCTION> INSTALL> E-RDS, COM-TEST, COM-LOG,
RGW-ADR
Supplement/memo Embedded-RDS: Function to send device information such as the
device counter, failure, and consumables to the sales company's
server via SOAP protocol
8-98
8-98