Canon imageRUNNER ADVANCE 6075 Series Service Manual page 693

E Detail
Location Item
Code Code
E041 -0002 -05 Title Left Deck Lifter Motor error
Remedy 1. Check for displacement of the Lifter Wire of the Left Deck.
2. Check for hindrance to smooth movement of the Deck
Base Plate of the Left Deck.
Description Overcurrent of the Leftt Deck Lifter Motor was detected.
E041 -0003 -05 Title Cassette 3 Lifter Motor error
Remedy 1. Check for error around the Lifter of the Cassette 3.
2. Check for hindrance to smooth movement of the Cassette
Base Plate of the Cassette 3.
Description Overcurrent of the Cassette 3 Lifter Motor was detected.
E041 -0004 -05 Title Cassette 4 Lifter Motor error
Remedy 1. Check for error around the Lifter of the Cassette 4.
2. Check for hindrance to smooth movement of the Cassette
Base Plate of the Cassette 4.
Description Overcurrent of the Cassette 4 Lifter Motor was detected.
E053 -0001 -05 Title Error in Reverse Upper Flapper Solenoid connection
detection
Remedy 1. Check the connection of the Reverse Upper Flapper
Solenoid (SL5).
Solenoid side: J2115, Duplex Driver PCB side: J340
2. Replace the Reverse Upper Flapper Solenoid (SL5).
3. Replace the Duplex Driver PCB (PCB4).
4. Replace the DC Controller PCB (PCB1).
Description Connection of the Reverse Upper Flapper Solenoid (SL5)
cannot be detected 5 times with 20 msec time interval.
7
Error Code > Error Code > Error Code Details > E000 to E069
Description
7 Error Code > Error Code > Error Code Details > E000 to E069
E Detail
Location Item
Code Code
E060 -0001 -05 Title Primary Charging Shutter HP open error
Remedy 1. Check the position of the Primary Charging Shutter and the
Cleaning Pad.
1-A. In the case that the Primary Charging Shutter and the
Cleaning Pad fail to operate (stopped at HP at front side)
1-A-1. Check the connection of the Primary Charging Wire
1-A-2. Replace the Primary Charging Wire Cleaning Motor
1-B. In the case that the Primary Charging Shutter and the
Cleaning Pad are stopped at rear side (close operation
position)
1-B-1. Check the connection of the Primary Charging
1-B-2. Replace the Primary Charging Shutter Sensor
1-C. In the case that the Primary Charging Shutter and the
Cleaning Pad are stopped along the way
1-C-1. Check the loosening of screw on the Slider Pin and
1-C-2. Replace the Primary Charging Assembly.
1-D. In the case that the Primary Charging Shutter stops at
front side and the Cleaning Pad moves to rear side
1-D-1. Check if the Shutter Mounting Plate is deformed. If
1-D-2. Check the loosening of screw on the Slider Pin and
1-D-3. Replace the Primary Charging Assembly.
2. Replace the Main Driver PCB (PCB2).
3. Replace the DC Controller PCB (PCB1).
Description The Primary Charging Shutter Sensor (PS94) detects that the
shutter is opened although it is moved to the close position.
Description
Cleaning Motor (M6).
Motor side: J3017, J3060 (iR-ADV 8xxx)/J3160 (iR-
ADV 6xxx) (relay), PCB side: J3177 (relay), J107
(Main Driver PCB (PCB2))
(M6).
Shutter Sensor (PS94).
Sensor side: J2029, J3089 (relay), PCB side: J3088
(relay), J114 (Main Driver PCB (PCB2))
(PS94).
abrasion of the pin. Tighten the screw or replace the
Slider Pin.
so, replace the Shutter Unit.
abrasion of the pin. Tighten the screw or replace the
Slider Pin.
7-8
7-8