Canon imageRUNNER ADVANCE 6075 Series Service Manual page 824

Address bit Name
P004 15 Not used
14 Not used
13 Not used
12 Thermistor temperature difference
error detection
Fixing Sub Thermistor 2 > Fixing
Sub Thermistor 1
11 Thermistor temperature difference
error detection
Fixing Main Thermistor > Fixing Sub
Thermistor 2
10 Thermistor temperature difference
error detection
Fixing Sub Thermistor 2 > Fixing
Main Thermistor
9 Thermistor temperature difference
error detection
Fixing Main Thermistor > Fixing Sub
Thermistor 1
8 Thermistor temperature difference
error detection
Fixing Sub Thermistor 1 > Fixing
Main Thermistor
7 Thermistor Connection
6 Front Door Open Detection Switch
5 Fixing Feed Lever
4 Fixing Power Supply PCB 12V OFF PCB10
3 Outer Delivery Sensor
2 Not used
1 Fixing Motor Error
0 Fixing Power Supply Cooling Fan
Error
8
Service Mode > COPIER > I/O (I/O display mode)
Symbol Remarks
-
-
-
THM2/ 1: Error
THM3 * The value returns to 0 when
temperature of the Fixing Assembly
decreases.
THM1/ 1: Error
THM3 * The value returns to 0 when
temperature of the Fixing Assembly
decreases.
THM1/ 1: Error
THM3 * The value returns to 0 when
temperature of the Fixing Assembly
decreases.
THM1/ 1: Error
THM2 * The value returns to 0 when
temperature of the Fixing Assembly
decreases.
THM1/ 1: Error
THM2 * The value returns to 0 when
temperature of the Fixing Assembly
decreases.
THM1/ 0: Connect
THM3
SW2 0: Close, 1: Open
- 1: Fixing Feed Unit presence
1: 12V to Fixing Power Supply PCB
is OFF or safety circuit operation
PS36 1: Paper presence
-
M3 1: Stop
FM7 1: Stop
8 Service Mode > COPIER > I/O (I/O display mode)
Address bit Name
P005 15 Roller Bias OFF
14 Pre-transfer Charging PCB Remote PCB26
13 Develop High Voltage PCB Remote PCB12
12 Primary Charging High Voltage PCB
Remote
11 Fixing Motor ON
10 Fixing Motor CCW
9 Not used
8 Not used
7 Fixing Power Supply PCB 12V ON
6 Fixing Power Supply PCB Relay 2
ON
5 Fixing Power Supply PCB Relay 1
ON
4 Not used
3 Developer Lower Cooling Fan/
Developer Upper Cooling Fan Half
Speed
2 Developer Lower Cooling Fan/
Developer Upper Cooling Fan Full
Speed
1 Not used
0 Not used
P006 15 For R&D use
14 Not used
13 Not used
12 Multi Cassette Heater ON
11 Not used
10 Not used
9 Not used
8 Not used
7 Not used
6 Not used
5 Not used
4 Not used
3 For R&D use
2 For R&D use
1 Pre-transfer Charging Wire Cleaning
Motor ON 2
0 Pre-transfer Charging Wire Cleaning
Motor ON 1
8-42
Symbol Remarks
- 0: OFF, 1: ON
0: ON
0: ON
PCB11 0: ON
M3 1: ON
M3 0: CW (paper feed direction)
-
-
PCB10 0: 12V forcible OFF
- 1: ON
- 1: ON
-
FM30/ 1: Half Speed
FM31
FM30/ 1: Full Speed
FM31
-
-
-
-
-
H02 0: ON
-
-
-
-
-
-
-
-
-
-
M7 ON1/ON2 Signal=
0/0: Stop
0/1: Front -> Rear
1/0: Rear -> Front
M7 ON1/ON2 Signal=
0/0: Stop
0/1: Front -> Rear
1/0: Rear -> Front
8-42