Canon imageRUNNER ADVANCE 6075 Series Service Manual page 710

E Detail
Location Item
Code Code
E519 -0002 -05 Title Gear change home position error (Finisher-E1)
Remedy 1. The Gear Change Home Position Sensor (PI117) is faulty.
2. The wiring between the Finisher Controller PCB and Gear
Change Motor is faulty.
3. The gear change mechanism is faulty.
4. The Gear Change Motor (M110) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Gear Change Hhome Position Sensor does not turn ON
when the Gear Change Motor has been driven for 387 pulses.
E519 -8001 -05 Title Gear change home position error (Finisher-E1)
Remedy 1. The Gear Change Home Position Sensor (PI117) is faulty.
2. The wiring between the Finisher Controller PCB and Gear
Change Motor is faulty.
3. The gear change mechanism is faulty.
4. The Gear Change Motor (M110) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Gear Change Home Position Sensor does not turn OFF
when the Gear Change Motor has been driven for 387 pulses.
E530 -8001 -05 Title Front aligning plate home position error (Finisher-E1)
Remedy 1. The Front Aligning Plate Home Position Sensor (PI106) is
faulty.
2. The wiring between the Finisher Controller PCB and Front
Aligning Plate Motor is faulty.
3. The front aligning plate is faulty.
4. The Front Aligning Plate Motor (M103) is faulty.
5. The Finisher Controller PCB is faulty.
Description The aligning plate does not leave the Aligning Plate Front
Home Position Sensor when the Alignment Plate Front Motor
has been driven for 4 seconds.
E530 -8002 -05 Title Front aligning plate home position error (Finisher-E1)
Remedy 1. The front Aligning Plate Home Position Sensor (PI106) is
faulty.
2. The wiring between the Finisher Controller PCB and front
aligning plate Motor is faulty.
3. The front aligning plate is faulty.
4. The front aligning plate Motor (M103) is faulty.
5. The Finisher Controller PCB is faulty.
Description The aligning plate does not return to aligning plate front home
position Sensor when the alignment plate front Motor has
been driven for 4 seconds.
7
Error Code > Error Code > Error Code Details > E500 to E5F6
Description
7 Error Code > Error Code > Error Code Details > E500 to E5F6
E Detail
Location Item
Code Code
E531 -8001 -05 Title Staple home position error (Finisher-E1)
Remedy 1. The wiring between the Finisher Controller PCB and
Stapler is faulty.
2. The Stapler is faulty.
3. The Finisher Controller PCB is faulty.
Description The Stapler does not leave the staple home position when
the Staple Motor has been driven for 0.4 sec.
E531 -8002 -05 Title Staple home position error (Finisher-E1)
Remedy 1. The wiring between the Finisher Controller PCB and
Stapler is faulty.
2. The Stapler is faulty.
3. The Finisher Controller PCB is faulty.
Description The Stapler does not return to the staple home position when
the Staple Motor has been driven for 0.4 sec.
E532 -8001 -05 Title Stapler shift home position error (Finisher-E1)
Remedy 1. The Stapler Drive Home Position Sensor (PI110) is faulty.
2. The wiring between the Finisher Controller PCB and
Stapler Shift Motor is faulty.
3. The stapler shift base is faulty.
4. The Stapler Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Stapler does not leave the stapler shift home pposition
when the Stapler Shift Motor hasbeen driven for 5 seconds.
E532 -8002 -05 Title Stapler shift home position error (Finisher-E1)
Remedy 1. The Stapler Drive Home Position Sensor (PI110) is faulty.
2. The wiring between the Finisher Controller PCB and
Stapler Shift Motor is faulty.
3. The stapler shift base is faulty.
4. The Stapler Shift Motor (M105) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Stapler does not return to the stapler shift home position
when the Stapler Shift Motor has been driven for 20 seconds.
E535 -8001 -05 Title Swing home position error (Finisher-E1)
Remedy 1. The Swing Home Position Sensor (PI105) is faulty.
2. The wiring between the Finisher Controller PCB and Swing
Motor is faulty.
3. The swing mechanism is faulty.
4. The Swing Motor (M106) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Stapler does not leave the swing home position when the
Swing Motor has been driven for 3 seconds.
7-25
Description
7-25