Canon imageRUNNER ADVANCE 6075 Series Service Manual page 996

SORTER > OPTION
FDPL-SL Set soil prev for back of Saddle:Fin-E1
Lv.1 Details To set ON/OFF of the Feed Plate Engagement Solenoid at the time
of Saddle stacking operation.
When 1 is set, the Intermediate Feed Roller is disengaged by turning
OFF the Feed Plate Engagement Solenoid at the time of Saddle
stacking operation.
Set 1 when the back of paper is soiled by the Intermediate Feed
Roller. But the alignment condition of papers at the time of saddle
stitching decreases.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When the back of paper is soiled due to the Intermediate Feed Roller
at the time of Saddle stacking operation
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: ON (Engagement), 1: OFF (Disengagement)
Default value 0
STCR-DWN Set occasional misalign prev mode:Fin-E1
Lv.1 Details When misalignment in feed direction occurs at approx. every 30
sheets for thin/plain paper, set 1.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When misalignment in feed direction occurs occasionally for thin/
plain paper
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
8
Service Mode > SORTER > OPTION
8 Service Mode > SORTER > OPTION
SORTER > OPTION
BUFF-INT Ppr intvl after buffer ppr ejctn: Fin-E1
Lv.1 Details In case of paper with excessive upward curl, paper right after the
buffer paper is ejected at the Finisher hits the Stack Delivery Roller,
causing Saddle Delivery Sensor stationary jam.
When 1 is set, the jam can be avoided since the paper intervals
between the present and the following papers after the buffer paper
ejection become wider.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When stationary jam occurs at the Stack Delivery Roller at buffer
operation
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
PRCS-SP3 Proc Tr fd SPD decelerate ON/OFF: Fin-E1
Lv.1 Details To set whether to decelerate the speed to feed paper to the Process
Tray Stopper in the Process Tray of the Finisher.
Set 1 to 5 when misalignment (buckling on the trailing edge) occurs
in staple mode because papers without buffer return too much.
As the value is incremented by 1, the feed speed is decelerated by
50 mm/sec.
Use case When misalignment occurs for thin/plain paper in the staple mode
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When changing the setting, adjustment of Process Tray return
amount (SORTER> ADJUST> PRCS-RET) may be required.
Display/adj/set range 0 to 8
0: OFF (700 mm/sec), 1: ON (650 mm/sec), 2: ON (600 mm/sec), 3:
ON (550 mm/sec), 4: ON (500 mm/sec), 5: ON (450 mm/sec), 6 to 8:
Not used
Appropriate target value 5
Default value 0
Related service mode SORTER> ADJUST> PRCS-RET
8-214
T-8-91
8-214