Canon imageRUNNER ADVANCE 6075 Series Service Manual page 901

COPIER > OPTION > FNC-SW
MODELSZ2 Ppr size dtct global support in bookmode
Lv.2 Details To set ON/OFF for global support of document size detection in
copyboard reading mode.
Use case Upon user's request (mixed media original with AB/Inch
configuration)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution - Do not use this at the normal service.
- The Document Size Sensor (Photo Sensor) is additionally required
to correctly detect the document size when the original consists of
mixed media (AB/Inch configuration).
Display/adj/set range 0 to 1
0: Detected with detection size according to location, 1: Detected
with AB/Inch mixed media.
Default value 0
SVMD-ENT Setting of entry method to service mode
Lv.2 Details To set the way to get in service mode to prevent information leak.
Use case As needed
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: [Settings/Registration] - Pressing [2] and [8] at the same time -
[Settings/Registration]
1: [Settings/Registration] - Pressing [4] and [9] at the same time -
[Settings/Registration]
Default value 0
BASE-SW Model switch set from MEAP-Full to Base
Lv.1 Details To switch from the MEAP-Full model to the Base model.
Switch this mode in the case of restricting the operation of MEAP
application for trouble analysis.
Use case When trouble that caused by MEAP application occurs
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Switching from the Base model to the MEAP-Full model is not
available.
Display/adj/set range 0 to 1
0: OFF (Base model), 1: ON (Full model)
Default value Depending on the setting of option bit (MeapModelBIT).
8
Service Mode > COPIER > OPTION > FNC-SW
8 Service Mode > COPIER > OPTION > FNC-SW
COPIER > OPTION > FNC-SW
SC-L-CNT Set large paper jdgmt reference at scan
Lv.1 Details To set the judgment reference of the scan counter as to which to use
B4 or LTR to determine large size.
The threshold is determined by the combination with the setting of
B4-L-CNT.
SC-L-CNT=0, B4-L-CNT=0: paper exceeding B4 is determined as
large size, paper with B4 or smaller is determined as small size.
SC-L-CNT=0, B4-L-CNT=1: paper with B4 or larger is determined as
large size, paper smaller than B4 is determined as small size.
Use case As needed
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: B4 size, 1: LTR size
Default value 0
Related service mode COPIER> OPTION> USER> B4-L-CNT
CKT-LANG Setting of China/Korea/Taiwan mode
Lv.2 Details To set China/Korea/Taiwan mode.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
KSIZE-SW Set of Chinese paper (K-size) support
Lv.2 Details To set to detect/display the Chinese paper (K size paper: 8K, 16K).
Use case When using K size paper
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Go through the following: COPIER > OPTION > FNC-SW > MODEL-
SZ; and if MODEL-SZ is "0: AB configuration", this mode is enabled.
Display/adj/set range 0 to 1
0: Not supported, 1: Supported
Default value 0
Related service mode COPIER> OPTION> FNC-SW> MODEL-SZ
Supplement/memo 8K paper: 270 x 390 mm, 16K paper: 270 x 195 mm
PDF-RDCT PDF reduction set at forwarding
Lv.2 Details To set whether to reduce the image for transmission when converting
the image received by IFAX into PDF for e-mail/file transmission.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Following the current setting, 1: Image reduction
Default value 0
8-119
8-119