Canon imageRUNNER ADVANCE 6075 Series Service Manual page 992

SORTER > ADJUST
THC-CL Heavy ppr curl prevention mode:Fin-E1
Lv.1 Details Set 1 when upward curl occurs on the heavy paper delivered.
When 1 is set, the amount of Stack Tray descension for stack
delivery increases. The paper surface detection is performed for
every sheet, not for every 5 sheets.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When upward curl occurs on the heavy paper delivered
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
THC-PUSH Heavy ppr out prevention mode:Fin-E1
Lv.1 Details Set 1 when the already stacked paper is pushed out at the time of
heavy paper delivery.
When 1 is set, the Stack Tray moves down temporarily before the
heavy paper is delivered to the Processing Tray if the leading sheet
is heavy paper.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When the already stacked paper is pushed out at the time of heavy
paper delivery
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
OFST-STC Poor offset stack prev mode:Fin-E1
Lv.1 Details Set 1 when paper is not appropriately stacked in the small-size offset
mode.
When 1 is set, buffer operation is not performed in the small-size
offset mode.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When paper is not appropriately stacked in the small-size offset
mode
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
8
Service Mode > SORTER > ADJUST
8 Service Mode > SORTER > ADJUST
SORTER > ADJUST
THN-STC Poor thin ppr stack prev mode:Fin-E1
Lv.1 Details Set 1 when thin paper is not appropriately stacked.
When 1 is set, the stacking condition of thin paper improves.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When thin paper is not appropriately stacked
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
STP-P-CH Stpl stack displace prev mode:Fin-E1
Lv.1 Details Set 1 when the paper on the top is misaligned in the staple delivery
mode.
When 1 is set, paper stack alignment operation is executed twice
immediately before stapling.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When the paper on the top is misaligned in the staple delivery mode
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
TRY-NIS Tray switch noise reduct mode:Fin-E1
Lv.1 Details Set 1 when the operation noise after switching the Stack Tray is loud.
When 1 is set, the Stack Tray rise operation becomes slow.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When the operation noise after switching the Stack Tray is loud
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
TRY-SU Tray switching speedup mode: Fin-E1
Lv.1 Details Set 1 when the Stack Tray switching time is long.
When 1 is set, the Stack Tray rise speed becomes fast.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When the Stack Tray switching time is long
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
8-210
8-210