Canon imageRUNNER ADVANCE 6075 Series Service Manual page 990

SORTER > ADJUST
SDL-ALG Adj of Saddle Stitcher alignment width
Lv.1 Details To adjust the alignment width of Saddle Stitcher.
As the value is incremented by 1, the alignment width is increased
by 0.5 mm.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When the misalignment occurs within a paper stack on the Saddle
Stitcher
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -20 to 20
Unit 0.5 mm
Default value 0
ST-ALG1 Adj Stacker A4 size align pstn:Fin-E1
Lv.1 Details To adjust the A4 size paper alignment position.
As the value is incremented by 1, the travel length of the Alignment
Plate is increased by 0.42mm.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When misalignment occurs in A4 size paper
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range -10 to 10
Unit 0.42 mm
Appropriate target value 0
Default value 0
ST-ALG2 Adj Stckr LTR size align pstn:Fin-E1
Lv.1 Details To adjust the LTR size paper alignment position.
As the value is incremented by 1, the travel length of the Alignment
Plate is increased by 0.42mm.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When misalignment occurs in LTR size paper
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range -10 to 10
Unit 0.42 mm
Appropriate target value 0
Default value 0
8
Service Mode > SORTER > ADJUST
8 Service Mode > SORTER > ADJUST
SORTER > ADJUST
STP-F3 A4R front stpl pstn (<45 deg): Fin-E1
Lv.1 Details To adjust the one front staple position on the A4R size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When misalignment occurs at the front staple position on A4R size
paper
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range -6 to 6
Unit 0.49 mm
Appropriate target value 0
Default value 0
STP-F4 LTRR frt stpl pstn (<45 deg): Fin-E1
Lv.1 Details To adjust the one front staple position on the LTRR size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When misalignment occurs at the front staple position on LTRR size
paper
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range -6 to 6
Unit 0.49 mm
Appropriate target value 0
Default value 0
STP-R3 A4R rear stpl pstn (<45 deg): Fin-E1
Lv.1 Details To adjust the one rear staple position on the A4R size paper.
As the value is incremented by 1, the staple position moves to the
rear side by 0.49mm.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When misalignment occurs at the rear staple position on A4R size
paper
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range -6 to 6
Unit 0.49 mm
Appropriate target value 0
Default value 0
8-208
8-208