Canon imageRUNNER ADVANCE 6075 Series Service Manual page 856

COPIER > ADJUST > CCD
MTF2-M10 MTF value 10 setting: horz scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-M11 MTF value 11 setting: horz scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-M12 MTF value 12 setting: horz scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-S10 MTF value 10 setting: vert scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-S11 MTF value 11 setting: vert scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
8
Service Mode > COPIER > ADJUST > CCD
8 Service Mode > COPIER > ADJUST > CCD
COPIER > ADJUST > CCD
MTF2-S12 MTF value 12 setting: vert scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF-M10 MTF value 10 setting: horz scan [Back]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF-M11 MTF value 11 setting: horz scan [Back]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF-M12 MTF value 12 setting: horz scan [Back]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF-S10 MTF value 10 setting: vert scan [Back]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
8-74
8-74