Canon imageRUNNER ADVANCE 6075 Series Service Manual page 873

COPIER > ADJUST > FEED-ADJ
ADJ-DK Write start pstn in horz scan:Deck/POD D
Lv.1 Details To adjust the image write start position in the horizontal scanning
direction when feeding paper from the Paper Deck/ POD Deck Lite.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Left margin becomes larger. (An image moves to the right.)
-: Left margin becomes smaller. (An image moves to the left.)
When replacing the DC Controller PCB/clearing RAM data, enter the
value of service label.
Use case When replacing the DC Controller PCB/clearing RAM data
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Caution If write start position cannot be adjusted in service mode, execute
mechanical adjustment.
Display/adj/set range -20 to 20
Unit 0.1 mm
Default value 0
ADJ-REFE Write start pstn in horz scan: 2nd side
Lv.1 Details To adjust the image write start position on the second side in the
horizontal scanning direction.
The image write start position is set in the relative amount against
the first side regardless of the paper pickup cassette/tray/deck.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Left margin becomes larger. (An image moves to the right.)
-: Left margin becomes smaller. (An image moves to the left.)
When replacing the DC Controller PCB/clearing RAM data, enter the
value of service label.
Use case When replacing the DC Controller PCB/clearing RAM data
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value 0
RG-MF Rgst start timing adj: MP Tray, Plain
Lv.1 Details To adjust the top margin by changing the timing to turn ON the
Registration Motor when feeding plain paper from the Multi-purpose
Tray.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Top margin becomes smaller. (An image moves upward.)
-: Top margin becomes larger. (An image moves downward.)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value -20
8
Service Mode > COPIER > ADJUST > FEED-ADJ
8 Service Mode > COPIER > ADJUST > FEED-ADJ
COPIER > ADJUST > FEED-ADJ
REG-THCK Rgst start timing adj: Heavy, 1/2 speed
Lv.1 Details To adjust the top margin by changing the timing to turn ON the
Registration Motor when feeding heavy paper.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Top margin becomes smaller. (An image moves upward.)
-: Top margin becomes larger. (An image moves downward.)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value -20
REG-OHT Rgst start timing adj: Transp, 1/2 speed
Lv.1 Details To adjust the top margin by changing the timing to turn ON the
Registration Motor when feeding transparency.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Top margin becomes smaller. (An image moves upward.)
-: Top margin becomes larger. (An image moves downward.)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value -20
REG-DUP1 Rgst start timing adj: Plain, 2nd side
Lv.1 Details To adjust the top margin by changing the timing to turn ON the
Registration Motor when feeding the second side of plain paper.
As the value is incremented by 1, the margin on the left edge of
paper is increased by 0.1 mm.
+: Top margin becomes smaller. (An image moves upward.)
-: Top margin becomes larger. (An image moves downward.)
Adj/set/operate method Enter the setting value (switch negative/positive by -/+ key) and
press OK key.
Display/adj/set range -50 to 50
Unit 0.1 mm
Default value -10
8-91
8-91