Canon imageRUNNER ADVANCE 6075 Series Service Manual page 941

COPIER > OPTION > USER
BCNT-AST Set of box print charge target job
Lv.1 Details To set the job type that advances the count in box print with NE
Controller (ASSIST).
Use case When switching the job type that is subject to counting of the box
print with NE Controller
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: PDL job, 1: Copy job
Default value 0
PRJOB-CP Set count TX at RX/report print
Lv.2 Details To set to enable/disable a page-basis count pulse transmission to the
charging management device at the time of reception print or report
print.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: No transmission, 1: Transmission
Default value 0
Supplement/memo Charging management device: Coin Manager, Non-Canon-made
control card
DOC-REM Dis/hide of original removal message
Lv.1 Details To set whether to display or hide the message to remove original
when scanning with DADF without opening/closing DADF after
scanning with the Copyboard.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
DPT-ID-7 Password entry set at dept ID reg/auth
Lv.2 Details To set whether to require a password entry at the time of registration/
authentication of department ID.
With the setting to require entry, entry of 7-digit password is required
as well as entry of department ID.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Department ID only, 1: 7-digit (password) entry
Default value 0
8
Service Mode > COPIER > OPTION > USER
8 Service Mode > COPIER > OPTION > USER
COPIER > OPTION > USER
RUI-RJT Connct set at invalid auth from remoteUI
Lv.2 Details To set to disconnect HTTP port when the machine receives invalid
authentication from remote UI 3 times.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Continued connection, 1: Disconnected
Default value 0
CTM-S06 Set of password delete from export file
Lv.2 Details To set to delete password for file transmission address from export
file.
With the setting to delete password, the password of file transmission
target is deleted at the time of exporting address book data from
remote UI.
Use case - Upon user's request
- When avoiding information leak
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Retained, 1: Deleted
Default value 0
FREG-SW Dis/hide of MEAP counter free rgst area
Lv.2 Details To set whether to display or hide the free register area of MEAP
counter for SEND
Use case At trouble analysis
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution - Do not use this at the normal service.
- Take necessary action in accordance with the instructions from the
Quality Support Division.
Display/adj/set range 0 to 1
0: Hide, 1: Display
Default value 0
Supplement/memo Individual count-up (counter advance) of MEAP application is
available in the free register area of MEAP counter.
8-159
8-159