Network - Canon imageRUNNER ADVANCE 6075 Series Service Manual

COPIER > TEST > PG
FINISH Accessory processing function test print
Lv.1 Details To execute the test print relating to accessory processing function.
Use case When checking operation of accessory processing function
Adj/set/operate method 1) Enter the number of sheets for PG-QTY, and then press OK key.
2) Enter the setting value, and then press OK key.
3) Press Start button.
The machine outputs a test print.
Display/adj/set range 0 to 99
0: N/A
1: Staple (front) *1
2: Staple (2 points) *1
3: Staple (rear) *1
4: Booklet (saddle stitch) *1
5: Z-fold (single sleeve) *1
6: 2-fold *1
7: C-fold *2
8: V-fold *2
9: 4-fold *2
10: Z-fold (out-3-fold) *2
11: Punch (Inner Puncher) *3
12: Multiple-hole punch *4
13: Shift *1
14 to 99: Spare (for future use)
*1 Finisher, *2 Multi-folding machine, *3 Inner Puncher, *4 Multiple-
hole Puncher
Default value 0
Related service mode COPIER> TEST> PG> PG-QTY
8
Service Mode > COPIER > TEST > NETWORK
T-8-72
8 Service Mode > COPIER > TEST > NETWORK

■ NETWORK

COPIER > TEST > NETWORK
PING Network connection check
Lv.1 Details To check connection between this machine and TCP/IP network.
Use case - When checking network connection at the time of installation
- At network connection failure
Adj/set/operate method 1) Turn OFF the main power switch.
2) Connect the network cable to this machine, and then turn ON the
main power switch.
3) Inform the system administrator at user's site that installation of
this machine is complete, and ask for network setting.
4) Ask the system administrator to check the network connection,
and check the remote host address of PING transmission target.
5) Select the item and enter the remote host address, and then press
OK key and Start key.
OK: Connection is normal. Checking procedure is complete.
NG: Connection failed. Go to step 6) if the cable connection is OK. In
case of cable connection failure, connect again and then go to step 5).
6) Select the item and enter loopback address, and then press OK
key and Start key.
OK: TCP/IP setting of this machine is normal. Go to step 7) to check
NIC.
NG: TCP/IP setting of this machine has failure. Go to step 3) to
check the setting again.
7) Select the item and enter the local host address, and then press
OK key.
OK: Network setting of this machine and NIC are normal. Inform the
system administrator that the trouble is due to network environment
and ask for countermeasure.
NG: Connection failure/fault with NIC. Check connection of NIC/
replace NIC.
Display/adj/set range 0.0.0.0 to 255.255.255.255
At normal state: OK
At failure occurrence: NG
Supplement/memo - Remote host address: IP address of PC terminal in network.
- Loopback address: 127.0.0.1. Checking TCP/IP of this machine is
available because the signal is returned before NIC.
- NIC: Network interface board
- Local host address: IP address of this machine
IPV6-ADR Setting of PING send address (IPv6)
Lv.1 Details To set the IPv6 address to send PING.
When PING is sent to this address by COPIER> TEST> NETWORK>
PING-IP6, the network connection condition in the IPv6 environment
can be checked.
Caution - Enter a consistent character string as an address of IPv6.
- Enter an address within 39 characters including hexadecimal
numbers (0-9, a-f) and a separator (:).
Related service mode COPIER> TEST> NETWORK> PING-IP6
8-185
8-185