Canon imageRUNNER ADVANCE 6075 Series Service Manual page 911

COPIER > OPTION > IMG-FIX
TMP-TBL5 Set fixing control temp table: Transp
Lv.1 Details To set the control temperature table of the Fixing Roller for
Transparency.
Use case When alleviating the curl
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -5 to 2: 0 degC
Unit 5 degC
Default value 0
TMP-TBL6 Set fixing control temp table: envlp
Lv.1 Details To set the control temperature table of the Fixing Roller for envelope.
Use case When alleviating the curl
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range -5 to 2: 0 degC
Unit 5 degC
Default value 0
RAG-CONT Set fix smeared image ctrl mode level
Lv.1 Details To set level of the mode (skipping) to control smeared image caused
by fixing area.
Use case When a smeared image occurs
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Set RAG-SW to 1 to 3 to enable skipping.
Display/adj/set range 0 to 3
0: No skipping, 1: Small skipping, 2: Medium skipping, 3: Large
skipping
Default value 0
Related service mode COPIER> OPTION> IMG-FIX> RAG-SW
RAG-SW ON/OFF of fixing burst prevention mode
Lv.1 Details To set ON/OFF of fixing burst prevention mode (skipping) to prevent
line burst.
Select "1: ON" in the case all horizontal lines are burst.
Set ON according to paper type in the case the degree of line burst
differs depending on media.
Use case When horizontal lines burst
Adj/set/operate method Enter the setting value, and then press OK key.
Caution Set RAG-CONT to 1 to 3 to enable skipping.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Related service mode COPIER> OPTION> IMG-FIX> RAG-CONT
8
Service Mode > COPIER > OPTION > IMG-FIX
8 Service Mode > COPIER > OPTION > IMG-FIX
COPIER > OPTION > IMG-FIX
FIX-DWN Set prdctvty reduct mode: small size
Lv.2 Details To set the speed ratio in the case of reducing productivity when
feeding small size paper.
Use case When an image failure (crepe mark) occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range -3 to 0
-3: 40%, -2: 60%, -1: 80%, 0: 100%
Default value 0
FIX-RT Set idle rotation time at last rotation
Lv.2 Details To set the idle rotation time at last rotation executed after a job is
completed.
Use case When an image failure (crepe mark) occurs
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 3
0: No idle rotation, 1: 10 seconds, 2: 20 seconds, 3: 30 seconds
Default value 0
P-BETWN Setting of paper interval: 2-sided mode
Lv.1 Details To set the paper interval at 2-sided mode.
Use this mode when uneven gloss occurs on the Fixing Roller pitch
(126 mm) on 1st side of 2-sided print.
When 1 is set, 150 mm or less paper interval at 2-sided mode
becomes 150 mm or more. Uneven gloss can be alleviated, but
productivity decreases.
Use case When uneven gloss occurs on 1st side of 2-sided print
Adj/set/operate method Enter the setting value, and then press OK key.
Caution When 1 is set, productivity decreases
Display/adj/set range 0 to 1
0: Normal, 1: Widening paper interval
Default value 0
FIX-TMP2 Set fixing/productivity: Plain paper A3+
Lv.1 Details To set priority between productivity and fixing by changing
temperature at which down sequence is applied to plain paper A3-
Extension (13"x19").
When 1 is set, fixing has priority over productivity because the
machine is likely to go into the down sequence.
When -1 is set, productivity has priority over fixing.
Use case When changing priority between fixing and productivity for plain
paper A3-Extension (13"x19")
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range -1 to 1
-1: Priority on productivity (-3 degC), 0: Normal, 1: Priority on fixing (+3
degC)
Unit 3 degC
Default value 0
8-129
8-129