Canon imageRUNNER ADVANCE 6075 Series Service Manual page 920

COPIER > OPTION > IMG-MCON
C-S-P-D High dens end edge crrct: PDL dens prrty
Lv.2 Details To set ON/OFF of high density trailing edge correction function at
PDL.
By selecting CAL (priority on density) in C-PDL-T, high density
trailing edge correction function is ON in normal operation; however,
set OFF as needed.
Use case ON: When reducing jagged line and jagged outline of text
OFF: When matching density with original on high density area, or
when prioritizing density and gradation
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Related service mode COPIER> OPTION> IMG-MCON> C-PDL-T
Supplement/memo Abbreviation of CAL_Shadow_PDL_Density
C-S-C-D High density end edge crrct ON/OFF: copy
Lv.2 Details To set ON/OFF of high density trailing edge correction function at
copy.
With CAL of COPY, high density trailing edge correction function is
ON in normal operation; however, set OFF as needed.
Use case ON: When reducing jagged line and jagged outline of text
OFF: When matching density with original on high density area, or
when prioritizing density and gradation
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
Supplement/memo Abbreviation of CAL_Shadow_COPY_Density. When adjusting the
input signal 255 to low in the case that the density of solid area is
too high, jaggy (jagged effect of halftone) may occur to text, etc. By
entering the input signal 255 as solid, occurrence of jaggy can be
prevented.
C-SM-P-G [Not used]
Lv.1 Details -
C-SM-C-G [Not used]
Lv.1 Details -
8
Service Mode > COPIER > OPTION > IMG-MCON
8 Service Mode > COPIER > OPTION > IMG-MCON
COPIER > OPTION > IMG-MCON
WDREDUCT Setting of white dots reduction mode
Lv.1 Details To set the white dots reduction mode.
When 1 is set, white dots become less significant by enlarging black
dots by thin line correction.
Use case When white dots are significant
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 0
Related service mode COPIER> OPTION> IMG-MCON> VDADDCNT, HDADDCNT, LIN-
OFST
Related user mode Thin line correction, horizontal line correction, and vertical line
correction in user mode
VDADDCNT Horz added dot amnt at white dots reduct
Lv.1 Details To adjust the amount of dots added to side at white dots reduction
mode.
As the greater value is set, the size of white dot gets smaller.
When WDREDUCT is 1, this setting is enabled.
Use case When adjusting the level of white dots reduction mode
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 4
Default value 1
Related service mode COPIER> OPTION> IMG-MCON> WDREDUCT
HDADDCNT Vert added dot amnt at white dots reduct
Lv.1 Details To adjust the amount of dots added to upside at white dots reduction
mode.
As the greater value is set, the size of white dot gets smaller.
When WDREDUCT is 1, this setting is enabled.
Use case When adjusting the level of white dots reduction mode
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 4
Default value 0
Related service mode COPIER> OPTION> IMG-MCON> WDREDUCT
LIN-OFST Set special paper added dot amnt offset
Lv.1 Details To set the offset amount of dots added to vertical/horizontal direction
when lines on special paper are thinner than those on plain paper.
When printing special paper, compared to plain paper, the amount of
dots specified with this item is added.
As the value is larger, lines become thicker.
When WDREDUCT is 0, this setting is enabled.
Use case When the line width of special paper is thinner than the one of plain
paper
Adj/set/operate method Enter the setting value, and then press OK key.
Display/adj/set range 0 to 4
Default value 1
Related service mode COPIER> OPTION> IMG-MCON> WDREDUCT
8-138
T-8-60
8-138