Canon imageRUNNER ADVANCE 6075 Series Service Manual page 779

Alarm
Title
Code
04-0075 Error in Reverse Movement: Jam occurred at the time of large size paper
Detachment Solenoid
connection Cause: Connection of the Reverse Detachment Solenoid (SL12)
cannot be detected.
Measures:
1. Check the connection of the Reverse Detachment Solenoid
(SL12).
Solenoid side: J2176, Duplex Driver PCB side: J340
2. Replace the Reverse Detachment Solenoid (SL12).
3. Replace the Duplex Driver PCB (PCB4).
06-0003 Web absence notice Movement: The Web Drive Solenoid is turned ON 4 times after
Cause: Remaining level of the Fixing Cleaning Web is low.
Measures: Replace the Fixing Cleaning Web.
09-0006 2D Shading ROM Movement: Turn OFF the 2D Shading.
error 1 Cause: After clearing the drum, not reading the EEPROM.
Measures: Execute COPIER>FUNCTION>2D-SHADE>2D-
09-0007 2D Shading ROM Movement: Turn OFF the 2D Shading.
error 2 Cause: After reading ROM data, calculated checksum value
and checksum of ROM does not match.
Measures: Install the correct ROM.
09-0008 Drum HP signal noise Movement: Only when the 2D shading is ON, the accuracy of
alarm
Cause: The Drum HP cycle is shorter than the specified cycle.
Measures:
1. Install the Drum HP Sensor (PS61) and check the connector.
2. Check the Drum HP Flag.
3. Check the harness between the Drum HP Sensor (PS61)
and the Main Driver PCB (PCB2).
(Between J2137 and J107)
4. Replace the Drum HP Sensor (PS61).
5. Replace the Main Driver PCB (PCB2).
6. Check the harness between the Main Driver PCB (PCB2)
and the DCON PCB (PCB1).
(Between J125 and J411 and between J126 and J412)
7. Replace the DCON PCB (PCB1).
7
Error Code > Alarm Code > List of Alarm Code
A. movement /B. cause /C. measures
reverse delivery.
the Fixing Cleaning Web Level Sensor performs
detection.
READ.
shading is degraded and an image error occurs.
Uneven density may occur.
7 Error Code > Alarm Code > List of Alarm Code
Alarm
Title
Code
09-0009 Drum HP signal Movement: Only when the 2D shading is ON, the accuracy of
absence alarm
Cause: The Drum HP cycle is longer than the specified cycle.
Measures:
1. Install the Drum HP Sensor (PS61) and check the connector.
2. Check the Drum HP Flag.
3. Check the harness between the Drum HP Sensor (PS61)
and the Main Driver PCB (PCB2).
(Between J2137 and J107)
4. Replace the Drum HP Sensor (PS61).
5. Replace the Main Driver PCB (PCB2).
6. Check the harness between the Main Driver PCB (PCB2)
and the DCON PCB (PCB1).
(Between J125 and J411 and between J126 and J412)
7. Replace the DCON PCB (PCB1).
10-0001 No toner (Bk) (RDS -
creates)
11-0002 Waste Toner Movement: A message "The waste toner container is full." is
Container full
(Photosensitive Drum)
Cause: The Waste Toner Counter reaches 600000.
Measures: Clean the Waste Toner Container. Reset the Waste
30-0004 Pre-transfer Charging Movement: Pre-transfer charging high voltage is not output. An
PCB Harness
disconnection Cause: Connection error of the Pre-transfer Charging PCB
(connection error) (PCB26).
Measures:
1. Check the connection between the Main Driver PCB (PCB2)
and the High Voltage Unit.
Main Driver PCB side: J112, High Voltage Unit side: J3098
2. Check the connection inside of the High Voltage Unit.
High Voltage Unit inlet side: J3098, Pre-transfer Charging
PCB side: J3544
3. Replace the Pre-transfer Charging PCB (PCB26).
4. Replace the Main Driver PCB (PCB2).
31-0005 Environment Sensor Movement: It becomes as follow: environment temperature= 0
reading alarm
Cause: Connection of the Environment Sensor cannot be
detected.
Measures:
1. Check the connection of the Environment Sensor (THU1).
2. Replace the Environment Sensor (THU1).
A. movement /B. cause /C. measures
shading is degraded and an image error occurs.
Uneven density may occur.
displayed on the Control Panel, and the machine is
stopped.
Toner Counter.
image error like discharge trace occurs.
degC, environment humidity= 0%.
7-94
7-94