Canon imageRUNNER ADVANCE 6075 Series Service Manual page 904

COPIER > OPTION > FNC-SW
CE/SCNR Dis/set scan connector disconnect times
Lv.1 Details To display/change the number of Scanner connector disconnection
detection.
To count up every time when connector disconnection is detected.
When 0 is set, the number of detection can be reset.
Use case When checking/clearing the number of connector disconnection
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 5
Default value 0
Supplement/memo When the connector is disconnected, "Check the connector" is
displayed on the Control Panel.
After detecting certain times, an error code (E732-000) is displayed.
RPT2SIDE Set of report 1-sided/2-sided output
Lv.1 Details To set whether to use 1-sided or 2-sided for report output of service
mode.
Use case When making 2-sided report output to reduce the number of output
pages
Display/adj/set range 0 to 1
0: 1-sided, 1: 2-sided
Default value 0
Related service mode COPIER> FUNCTION> MISC-P> P-PRINT
BRWS-FAV Set of service browser favorite register
Lv.2 Details To set whether to allow registration of favorites in the browser for
service.
When 1 is set, favorites in the browser for service can be edited, and
any URLs can be accessed.
Use case When service engineers edit favorites in the browser for service
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Disabled, 1: Enabled
Default value 0
STND-PNL Set Upright Control Panel installation
Lv.2 Details To set whether the Upright Control Panel is installed.
When the Upright Control Panel is installed, set "1: Installed".
Use case At installation of the Upright Control Panel
Display/adj/set range 0 to 1
0: Not installed, 1: Installed
Default value 0
8
Service Mode > COPIER > OPTION > FNC-SW
8 Service Mode > COPIER > OPTION > FNC-SW
COPIER > OPTION > FNC-SW
INVALPDL Disable of PDL license
Lv.1 Details To disable the registered PDL license.
When "1: Disabled" is set, PDL is disabled even if a PDL license
is registered. This is set to the machines installed at convenience
stores, which do not allow PDL to be used.
Use case When prohibiting the use of PDL
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Registered PDL license is enabled, 1: Disabled
Default value 0
IMGCNTPR Setting of image quality mode
Lv.1 Details To set the image quality mode.
The counter priority mode is applied when 1 is set, and the image
quality priority mode is applied when 0 is set.
Use case Upon user's request
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Image quality priority mode, 1: Counter priority mode
Default value 0
CDS-FIRM Set to allow firmware update by admin
Lv.1 Details To set whether to permit update of the firmware by user
(administrator).
When "1: Enabled" is set, Updater can be activated from the user
mode.
Use case When allowing the administrator to update the firmware
Display/adj/set range 0 to 1
0: Disabled, 1: Enabled
Default value Europe: 1, Other than Europe: 0
Supplement/memo CDS: Content Delivery System
CDS-MEAP Set to allow MEAP installation by admin
Lv.1 Details To set whether to permit the user (administrator) to install MEAP
applications and enable iR options from CDS.
When "1: Enabled" is set, Updater can be activated from the user
mode.
Use case When allowing the administrator to install MEAP applications and
enable iR options from CDS
Display/adj/set range 0 to 1
0: Disabled, 1: Enabled (This setting can be specified for China,
Korea and Taiwan models only.)
Default value 1
Supplement/memo CDS: Content Delivery System
8-122
8-122