Canon imageRUNNER ADVANCE 6075 Series Service Manual page 849

COPIER > ADJUST > CCD
DFTAR-R Shading target value (R) [Front side]
Lv.1 Details When replacing the Reader Controller PCB, enter the value of
service label.
When replacing the Copyboard Glass/Scanner Unit (paper front),
execute COPIER> FUNCTION> CCD> DF-WLVL1, DF-WLVL2 and
write the value which is automatically set in the service label.
Use case - When replacing the Reader Controller PCB/clearing RAM data
- When replacing the Copyboard Glass/Scanner Unit (paper front)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 700 to 1400
Default value 1159
Related service mode COPIER> FUNCTION> CCD> DF-WLVL1, DF-WLVL2
DFTAR-G Shading target value (G) [Front side]
Lv.1 Details When replacing the Reader Controller PCB, enter the value of
service label.
When replacing the Copyboard Glass/Scanner Unit (paper front),
execute COPIER> FUNCTION> CCD> DF-WLVL1, DF-WLVL2 and
write the value which is automatically set in the service label.
Use case - When replacing the Reader Controller PCB/clearing RAM data
- When replacing the Copyboard Glass/Scanner Unit (paper front)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 700 to 1400
Default value 1189
Related service mode COPIER> FUNCTION> CCD> DF-WLVL1, DF-WLVL2
DFTAR-B Shading target value (B) [Front side]
Lv.1 Details When replacing the Reader Controller PCB, enter the value of
service label.
When replacing the Copyboard Glass/Scanner Unit (paper front),
execute COPIER> FUNCTION> CCD> DF-WLVL1, DF-WLVL2 and
write the value which is automatically set in the service label.
Use case - When replacing the Reader Controller PCB/clearing RAM data
- When replacing the Copyboard Glass/Scanner Unit (paper front)
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 700 to 1400
Default value 1209
Related service mode COPIER> FUNCTION> CCD> DF-WLVL1, DF-WLVL2
8
Service Mode > COPIER > ADJUST > CCD
8 Service Mode > COPIER > ADJUST > CCD
COPIER > ADJUST > CCD
MTF2-M1 MTF value 1 setting: horz scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-M2 MTF value 2 setting: horz scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-M3 MTF value 3 setting: horz scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-M4 MTF value 4 setting: horz scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
MTF2-M5 MTF value 5 setting: horz scan [Front]
Lv.1 Details Setting value for MTF filter coefficient calculation.
Enter the value of service label on the Reader.
Use case When replacing the Reader Controller PCB/clearing RAM data
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 20 to 85
Default value 50
Related service mode COPIER> FUNCTION> CCD> MTF-CLC
8-67
8-67