Canon imageRUNNER ADVANCE 6075 Series Service Manual page 903

COPIER > OPTION > FNC-SW
UNLMTBND Over 400 binders print job support set
Lv.1 Details To set whether to support print job that exceeds 400 binders.
With the setting to support, the machine makes prints by sharing
binders according to job attribution.
Select "1: Not supported" if the user does not print job* with large
quantity of binders.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Automatic setting (When the print server is not connected: not
supported; When the print server is connected: supported)
1: Not supported
Default value 0
Supplement/memo * : A job that requires finishing (such as stapling) in one job. Does not
apply in the case of executing finishing with multiple sets of output.
MIBCOUNT Scope range set of Charge Counter MIB
Lv.2 Details To set the range of counter information that can be obtained as MIB
(Management Information Base).
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: All charge counters are obtained, 1: Only displayed counter* is
obtained, 2: All charge counters are not obtained
* : Counter specified by the following: COPIER > OPTION > USER >
COUNTER 1 to 6
Default value 0
Related service mode COPIER> OPTION> USER> COUNTER1 to 6
MEAP-PRI Setting of MEAP task priority
Lv.2 Details Selecting "1: ON" increases MEAP task priority.
Use case When improving processing performance of MEAP
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF, 1: ON
Default value 1
CNTR-SW Init of parts counter replacement timing
Lv.1 Details To return the estimated life of parts counter to the initial value.
Use case Upon user's request
Adj/set/operate method 1) Enter 0, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0: Returned to the initial value
Default value 0
8
Service Mode > COPIER > OPTION > FNC-SW
8 Service Mode > COPIER > OPTION > FNC-SW
COPIER > OPTION > FNC-SW
ILSZ-JAM ON/OFF of size difference jam detection
Lv.2 Details To set ON/OFF of size difference jam detection.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
W/RAID Setting of RAID Board installation
Lv.1 Details To set installation condition of RAID Board (HDD Mirroring Kit).
Select "1: Installed" when installing the RAID Board. Select "0: Not
installed" when removing the RAID Board.
Use case When installing/removing RAID Board
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Not installed, 1: Installed
Default value 0
PSWD-SW Password type set to enter service mode
Lv.1 Details To set the type of password that is required to enter when getting into
service mode.
2 types are available: one for "service technician" and the other for
"system administrator + service technician".
When selecting the type for "system administrator + service
technician", enter the password for service technician after the
password entry by the user's system administrator.
Use case Upon request from the user who concerns security
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: No password, 1: Service technician, 2: System administrator +
service technician
Default value 0
SM-PSWD Password setting for service technician
Lv.2 Details To set password for service technician that is used when getting into
service mode.
Use case When password is required to get into service mode
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution Be sure to select 1 or 2 with PSWD-SW in advance.
Display/adj/set range 1 to 99999999
Default value 11111111
Related service mode COPIER> OPTION> FNC-SW> PSWD-SW
8-121
8-121