Canon imageRUNNER ADVANCE 6075 Series Service Manual page 995

OPTION
SORTER > OPTION
BLNK-SW Set Saddle Finisher fold position margin
Lv.1 Details To set the margin width of fold position on Saddle Finisher.
Use case When changing the margin width of fold position
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 2
0: Normal, 1: Wider, 2: Entire image (no margin)
Default value 2
MD-SPRTN Restricted operation at Finisher error
Lv.1 Details To set whether to stop the machine when an error occurs at Finisher.
Use case When preferring to run the machine at Finisher error occurrence
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When "1" is set, staple operation or alignment operation is not
executed. Set "0" normally.
Display/adj/set range 0 to 1
0: Normal, 1: Restricted operation
Default value 0
BUFF-SW Setting Finisher buffer operation:Fin-E1
Lv.1 Details To set ON/OFF of buffer operation in the Finisher.
Set 1 in case of misalignment due to charging between papers in
staple mode for small size papers.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When misalignment of paper stack occurs in staple mode for small
size papers
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Caution When the buffer operation is set to OFF, productivity decreases.
Display/adj/set range 0 to 1
0: ON, 1: OFF
Default value 0
8
Service Mode > SORTER > OPTION
8 Service Mode > SORTER > OPTION
SORTER > OPTION
TRY-OVER Set of fold ppr stack limit: Fin-E1
Lv.1 Details To set the limit of stack capacity for small size Z-fold paper.
When clearing the limit of stack capacity, paper can be stacked
beyond the maximum stack capacity.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When stacking the paper beyond the maximum stack capacity of the
Tray.
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Normal operation, 1: Clearing limit of stack capacity
Default value 0
PRCS-SP1 Proc Tr fd SPD accelerate ON/OFF: Fin-E1
Lv.1 Details To set whether to accelerate the speed to feed paper to the Process
Tray Stopper in the Process Tray of the Finisher.
When misalignment occurs in the sort and staple mode due to paper
return failure, set 1.
Use case When misalignment occurs in the sort and staple mode
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: OFF (600mm/sec), 1: ON (700mm/sec)
Default value 0
RTNRL-UP Set Inserter pckup ppr drop prev:Fin-E1
Lv.1 Details To set the Paper Return Roller rise timing when stacking papers
2
(256g/m or more) picked up from the Inserter on the Process Tray.
Set 1 if papers picked up from the Inserter fall from the Finisher Tray
when stacking on the Process Tray.
The item can be also set with DIP switch of the Finisher (with
common setting range and setting value). The latest setting value is
enabled regardless of service mode/DIP switch.
Use case When papers picked up from the Inserter fall from the Finisher Tray
at the time of stacking on the Process Tray
Adj/set/operate method 1) Enter the setting value, and then press OK key.
2) Turn OFF/ON the main power switch.
Display/adj/set range 0 to 1
0: Normal, 1: Slow down
Default value 0
8-213
8-213