Canon imageRUNNER ADVANCE 6075 Series Service Manual page 813

COPIER > DISPLAY > ACC-STS
DATA-CON Dis of NE Controller connection state
Lv.1 Details To display the connecting state of NE Controller.
Use case When checking the connection between the machine and the NE
Controller
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 1
0: Not connected, 1: Connected
RAM Display of MNCON PCB memory capacity
Lv.1 Details To display the memory capacity of the Main Controller PCB.
Use case When checking the memory capacity of the machine
Adj/set/operate method N/A (Display only)
Unit MB
Default value 512
COINROBO Dis of Coin Manager connection state
Lv.1 Details To display the connecting state of the Coin Manager.
Use case When checking the connection between the machine and the Coin
Manager
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 1
0: Not connected, 1: Connected
NIB Display of Network PCB connection state
Lv.1 Details To display the connecting state of the Network PCB.
Use case When checking the connection between the machine and the
Network PCB
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 3
0: Not connected, 1: Ethernet PCB connected, 2: Token Ring PCB
connected, 3: Ethernet PCB + Token Ring PCB connected
PS/PCL Install state dis of PS/PCL firmware
Lv.1 Details To display the installation state of PS/PCL firmware.
Use case When checking whether NetWare firmware is installed to the
machine
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 2
0: Not installed, 1: PS/PCL, 2: PS Kanji
NETWARE Dis of NetWare firmware install state
Lv.1 Details To display the installation state of the NetWare firmware.
Use case When checking whether NetWare firmware is installed to the
machine
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 1
0: Not installed, 1: Installed
8
Service Mode > COPIER > DISPLAY > ACC-STS
8 Service Mode > COPIER > DISPLAY > ACC-STS
COPIER > DISPLAY > ACC-STS
SEND Display of SEND support PCB existence
Lv.1 Details To display whether there is PCB to support SEND function.
SEND function can be used only when the PCB is mounted.
Use case When checking the connection between the machine and the PCB
that supports SEND function
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 1
0: Not mounted, 1: Mounted
TRIM-CN Display of Trimmer connection state
Lv.1 Details To display the connecting state of Trimmer.
Use case When checking the connection between the machine and Trimmer
Adj/set/operate method N/A (Display only)
Display/adj/set range 0 to 1
0: Not connected, 1: Connected
HDD Display of HDD model name
Lv.1 Details To display the model name of HDD.
Use case When checking the model name of HDD used on the machine
Adj/set/operate method N/A (Display only)
PCI1 Display of PCI1-connected PCB name
Lv.1 Details To display the name of the PCB that is connected to PCI1.
Use case When checking the name of the PCB that is connected to PCI1
Adj/set/operate method N/A (Display only)
Display/adj/set range -: No PCB connected
Voice Board: Voice PCB
3DES Board: Encryption PCB
1Gbit-Board: Giga Ethernet PCB
PCI2 Display of PCI2-connected PCB name
Lv.1 Details To display the name of the PCB that is connected to PCI2.
Use case When checking name of the PCB that is connected to PCI2
Adj/set/operate method N/A (Display only)
Display/adj/set range -: No PCB connected
iSLOT: iSLOT Wireless LAN PCB
Voice Board: Voice PCB
Voice Board R: Voice Recognition PCB (Display is hidden on this
machine.)
3DES Board: Encryption PCB
1Gbit-Board: Giga Ethernet PCB
IA-RAM Display of MNCON PCB memory(IA) capacity
Lv.1 Details To display the memory (IA) capacity of the Main Controller PCB.
Use case When checking the memory capacity of the Main Controller PCB
Adj/set/operate method N/A (Display only)
Unit MB
Default value 512
8-31
T-8-4
8-31