Canon imageRUNNER ADVANCE 6075 Series Service Manual page 711

E Detail
Location Item
Code Code
E535 -8002 -05 Title Swing home position error (Finisher-E1)
Remedy 1. The Swing Home Position Sensor (PI105) is faulty.
2. The wiring between the Finisher Controller PCB and Swing
Motor is faulty.
3. The swing mechanism is faulty.
4. The Swing Motor (M106) is faulty.
5. The Finisher Controller PCB is faulty.
Description The Stapler does not return to the swing home position when
the Swing Motor has bee driven for 3 seconds.
E537 -8001 -05 Title Rear aligning plate home position error (Finisher-E1)
Remedy 1. The Aligning Plate Rear Home Position Sensor (PI107) is
faulty.
2. The wiring between the Finisher Controller PCB and
Aligning Plate Rear Motor is faulty.
3. The rear aligning plate is faulty.
4. The Rear Aligning Plate Motor (M104) is faulty.
5. The Finisher Controller PCB is faulty.
Description The aligning plate does not leave the Aligning Plate Rear
Home Position Sensor when the Alignment Plate Rear Motor
has been driven for 4 seconds.
E537 -8002 -05 Title Rear aligning plate home position error (Finisher-E1)
Remedy 1. The Aligning Plate Rear Home Position Sensor (PI107) is
faulty.
2. The wiring between the Finisher Controller PCB and
Aligning Plate Rear Motor is faulty.
3. The rear aligning plate is faulty.
4. The Rear Aligning Plate Motor (M104) is faulty.
5. The Finisher Controller PCB is faulty.
Description The aligning plate does not return to Aligning Plate Rear
Home Position Sensor when the Alignment Plate Rear Motor
has been driven for 4 seconds.
E540 -8001 -05 Title Tray 1 time out error (Finisher-E1)
Remedy 1. The Tray 1 Shift Area Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1
Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description 1. If the tray does not return to home position when the Tray 1
Shift Motor is driven for 25 seconds.
2. If the tray does not move to other area when Tray 1 Shift
Motor is driven for 5 seconds.
7
Error Code > Error Code > Error Code Details > E500 to E5F6
Description
7 Error Code > Error Code > Error Code Details > E500 to E5F6
E Detail
Location Item
Code Code
E540 -8002 -05 Title Tray 1 shift area error (Finisher-E1)
Remedy 1. The Tray 1 Shift Area Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1
Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description 1. The dangerous area is reached before the Tray 1 Paper
Surface Sensor detects paper surface during the paper
surface detection operation.
2. A discontinuous area is detected during tray operation.
E540 -8003 -05 Title Swing Guide Switch/Staple Safety Switch error (Finisher-E1)
Remedy 1. The Tray 1 Shift Area Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1
Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description The swing guide switch or staple safety switch is activated
while the tray is operating.
E540 -8004 -05 Title The Tray 1 Shift Motor clock error (Finisher-E1)
Remedy 1. The Tray 1 Shift Area Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1
Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description The FG input cannot be detected when the Tray 1 Shift Motor
has been driven for 0.2 second.
E540 -8005 -05 Title The Tray 1 Shift Motor speed error (Finisher-E1)
Remedy 1. The Tray 1 Shift Area Sensor PCB is faulty.
2. The wiring between the Finisher Controller PCB and Tray 1
Shift Motor is faulty.
3. The tray up/down mechanism is faulty.
4. The Tray 1 Shift Motor (M107) is faulty.
5. The Finisher Controller PCB is faulty.
Description The lock detection signal turns OFF 150 msec after the lock
detection signal turned ON.
7-26
Description
7-26