Renault Laguna III Manual page 1888

Manual gearbox: Removal - Refitting
K9K, and TL4
a Screw on without tightening the upper bolts of the
manual gearbox.
a Torque tighten the upper bolts of the manual gear-
box (44 N.m).
a Fit the left-hand suspended engine mounting shaft
onto the manual gearbox.
a Screw on without tightening the bolts for the sus-
pended engine mounting on the gearbox.
a Torque tighten the bolts for the suspended engine
mounting on the gearbox (62 N.m).
III - FINAL OPERATION.
a Raise the engine using the tool (Mot. 1453) fitted
with the tool (Mot. 1453-01).
a Refit:
- the rubber pad on the left-hand suspended engine
mounting,
- the nuts of the rubber pad on the left-hand sus-
pended engine mounting.
a Bond the left-hand suspended engine mounting
shaft to the left-hand suspended engine mounting
rubber pad using the tool (Mot. 1453) fitted with the
tool (Mot. 1453-01).
a Refit the left-hand suspended engine mounting shaft
nut.
a Tighten the left-hand suspended engine mounting
shaft nut.
a Refit:
- the upper engine tie-bar,
- the upper engine tie-bar bolts.
a Tighten the upper engine tie-bar bolt on the engine.
a Torque tighten the upper engine tie-bar bolt on
the body (115 Nm).
a Remove the (Mot. 1453) then the (Mot. 1453-01).
a Refit the front axle subframe (see Front axle sub-
frame: Removal - Refitting) (31A, Front axle com-
ponents).
a Fit the power-assisted steering pipe.
a Refit the nut of the power-assisted steering pipe
bracket.
a Tighten the nut of the power-assisted steering pipe
bracket.
a Clip:
- the low pressure pipe on the front axle subframe,
MANUAL GEARBOX
21A-29
- the rigid brake pipe on the front left-hand side
member,
- the wiring on the left tie rod of the front axle sub-
frame.
a Connect the connector on the left-hand tie rod of the
front axle subframe.
a Refit:
- the nut of the power-assisted steering pipe of the
left-hand tie rod on the front axle subframe,
- the upper bolt of the left-hand tie-rod on the front
axle subframe.
a Tighten:
- the upper bolt of the left-hand tie-rod on the front
axle subframe,
- the nut of the power-assisted steering pipe from the
front axle subframe left-hand tie-rod.
a Refit:
- the radiator mounting cross member (see Radiator
mounting cross member: Removal - Refitting)
(41A, Front lower structure),
- the front right-hand driveshaft (see 29A, Drive-
shafts, Front right-hand driveshaft: Removal -
Refitting, page 29A-7) .
- the front left-hand driveshaft (see 29A, Drive-
shafts, Front left-hand driveshaft: Removal -
Refitting, page 29A-1) .
a Fill the manual gearbox (see 21A, Manual gearbox,
Manual gearbox oils: Draining - Filling, page
21A-2) .
a Refit:
- the front wheel arch liners (see Front wheel arch
liner: Removal - Refitting) (55A, Exterior protec-
tion),
- the wheels (see Wheel: Removal - Refitting)
(35A, Wheels and tyres),
- the starter (see Starter: Removal - Refitting)
(16A, Starting - Charging).
a Clip on the gearbox:
- the breather pipe,
- the engine wiring harness channel.
a Remove the blanking plugs from the hydraulic clutch
control pipe openings.
a Connect the hydraulic clutch pipe.
a Bleed the hydraulic clutch circuit (see Clutch cir-
cuit: Bleed) (37A, Mechanical component controls).
21A