Siemens G130 List Manual page 46

2 Parameters
2.2 List of parameters
p0015 Macro drive unit / Macro drv unit
CU_G130_PN, Can be changed: C1
CU_G150_PN,
Data type: Unsigned32
CU_G130_DP,
P-Group: -
CU_G150_DP
Not for motor type: -
Min
0
Description: Runs the corresponding macro files.
The selected macro file must be available on the memory card/device memory.
Example:
p0015 = 6 --> the macro file PM000006.ACX is run.
Dependency: Refer to: p0700, p1000, p1500, r8570
Notice: After the value has been modified, no further parameter modifications can be made and the status is shown in r3996.
Modifications can be made again when r3996 = 0.
When executing a specific macro, the corresponding programmed settings are made and become active.
Note: The macros in the specified directory are displayed in r8570. r8570 is not in the expert list of the commissioning
software.
Macros available as standard are described in the technical documentation of the particular product.
p0015 Macro drive object / Macro DO
VECTOR_G, B_INF, Can be changed: C2(1)
TM31, TM120, TM150
Data type: Unsigned32
P-Group: Commands
Not for motor type: -
Min
0
Description: Runs the corresponding macro files.
The selected macro file must be available on the memory card/device memory.
Example:
p0015 = 6 --> the macro file PM000006.ACX is run.
Dependency: Refer to: p0700, p1000, p1500, r8570
Notice: After the value has been modified, no further parameter modifications can be made and the status is shown in r3996.
Modifications can be made again when r3996 = 0.
When executing a specific macro, the corresponding programmed settings are made and become active.
No errors were issued during quick commissioning (p3900 = 1) when writing to parameters of the QUICK_IBN group!
Note: The macros in the specified directory are displayed in r8570. r8570 is not in the expert list of the commissioning
software.
Macros available as standard are described in the technical documentation of the particular product.
p0016 Activate BOP user-defined list / BOP user list act
CU_G130_PN, Can be changed: C1, U, T
CU_G150_PN,
Data type: Integer16
CU_G130_DP,
P-Group: All groups
CU_G150_DP
Not for motor type: -
Min
0
Description: Setting for activating/deactivating the user-defined list for the Basic Operator Panel (BOP).
If p0016 = 1, then it is only possible to access parameters in the parameter list (p0013).
Value: 0:
1:
Dependency: Refer to: p0011, p0012, p0013
Note: The user-defined list can only be deactivated with p0011 = p0012
46
BOP user-defined list deactivated
BOP user-defined list activated
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
999999
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
999999
Calculated: -
Dyn. index: -
Unit group: -
Scaling: -
Max
1
List Manual (LH2), 07/2016, A5E03263479A
Access level: 1
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
1
Access level: 1
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
SINAMICS G130/G150