Suzuki Baleno Manual page 596

7B-26 AUTOMATIC TRANSMISSION (3 A/T)
TROUBLESHOOTING
STEP
1 Was "AUTOMATIC TRANSMISSION DIAGNOSTIC FLOW
TABLE" performed?
2 Check Transmission Range Sensor Circuit for Operation.
When using SUZUKI scan tool:
1) Connect SUZUKI scan tool to DLC with ignition switch OFF.
2) Turn ignition switch ON and check transmission range
signal (P, R, N, D, 2 or L) on display when shifting manual
selector to each range. See Fig. 1.
Is applicable range indicated?
When not using SUZUKI scan tool:
1) Turn ignition switch ON.
2) Check voltage at terminals C20-2, C20-3, C20-6, C20-12,
C20-16 and C20-17 for vehicle with WU-TWC (C21-8,
C21-9, C21-10, C21-19, C21-20 and C21-21 for vehicle
without WU-TWC) respectively with selector lever shifted
to each range. See Fig. 2.
Taking terminal C20-16 for vehicle with WU-TWC (C21-10
for vehicle without WU-TWC) as an example, is battery
voltage indicated only when selector lever is shifted to "2"
range and 0 V for other ranges as shown in Fig. 3?
Check voltage at other terminals likewise, referring to Fig. 3.
Are check results satisfactory?
3 Check Select Cable for Adjustment referring to "SELECT
CABLE" of "ON-VEHICLE SERVICE" in this section.
Is it adjusted correctly?
4 Check Transmission Range Sensor.
1) Remove TR sensor from A / T.
2) At each of P, R, N, D, 2 and L shift position, check continuity
between terminals as well as each terminal and sensor
case. See Fig. 4.
Continuity should be indicated only between those
terminals as shown in Fig. 4 and 5 at each shift position.
Continuity should not exist between any terminal and
sensor case.
Are check results satisfactory?
5 Check Transmission Range Sensor for Installation Position.
1) Install TR sensor to transmission referring to
"TRANSMISSION RANGE SENSOR" of "ON-VEHICLE
SERVICE" in this section.
2) Perform check as described in step 2 of this table.
Is check result satisfactory?
Fig. 1 for Step 2.
ACTION
Fig. 2 for Step 2.
When not using SUZUKI
scan tool:
YES
Go to Step 2. Go to
"AUTOMATIC
TRANSMISSION
DIAGNOSTIC
FLOW TABLE".
Intermittent Go to Step 3.
trouble. Check
for intermittent
referring to
"INTERMITTENT
AND POOR
CONNECTION"
in Section 0A.
Go to Step 4. Adjust.
Go to Step 5. Replace TR
sensor.
Transmission Check "Br/Y",
range sensor "W / B", "R/W",
maladjusted. "W/R", "Y / R",
"Y" or "R / B"
circuit for open
or short.
If wires and
connections are
OK, substitute a
known-good PCM
and recheck.
Fig. 3 for Step 2.
Terminal
C20-3 C20-2 C20-12
(C21-8) (C21-19) (C21-9) (C21-20)
Selector
l ever position
P B + V 0 V 0 V
R 0 V B + V 0 V
N 0 V 0 V B + V
D 0 V 0 V 0 V
2 0 V 0 V 0 V
L 0 V 0 V 0 V
NO
C20-6 C20-16 C20-17
(C21-10) (C21-21)
0 V 0 V 0 V
0 V 0 V 0 V
0 V 0 V 0 V
B + V 0 V 0 V
0 V B + V 0 V
0 V 0 V B + V