Table of Contents
Advertisement
Table of contents
4
4.1
Introduction ......................................................................................................
4.2
Service Information System (SIS) .........................................................................
4.3
Maintenance schedule and expected component life ...............................................
4.3.1
Specification of maintenance intervals ........................................................
4.3.2
Maintenance schedule .............................................................................
4.3.3
Expected component life .........................................................................
4.4
Cleaning activities .............................................................................................
4.4.1
Cleaning the IRB 910INV ..........................................................................
4.5
Inspection activities ...........................................................................................
4.5.1
Inspecting the information labels ................................................................
4.5.2
Inspecting the robot cabling .....................................................................
4.5.3
Inspecting the ball screw spline unit ...........................................................
4.5.4
Inspecting axis-3 mechanical stops ............................................................
4.5.5
Inspecting the bellows ..............................................................................
4.5.6
Inspecting timing belts ............................................................................
4.6
Lubrication activities ..........................................................................................
4.6.1
Lubricating the ball screw spline unit ..........................................................
4.7
Replacement/changing activities ..........................................................................
5
5.1
Introduction ......................................................................................................
5.2
General procedures ...........................................................................................
5.2.1
Cut the paint or surface on the robot before replacing parts ............................
5.3
Cable harness ..................................................................................................
5.3.1
Replacing the base harness ......................................................................
5.3.2
Replacing the internal harness ...................................................................
5.3.3
Replacing the process hub ........................................................................
5.3.4
Replacing the SMB unit and battery unit ......................................................
5.4
Base ...............................................................................................................
5.4.1
Replacing the base .................................................................................
5.4.2
Replacing the axis-1 timing belt .................................................................
5.5
Inner arm .........................................................................................................
5.5.1
Replacing the inner arm ...........................................................................
5.5.2
Replacing the axis-2 timing belt .................................................................
5.6
Outer arm ........................................................................................................
5.6.1
Replacing the mechanical stopper ..............................................................
5.6.2
Replacing the bellows ..............................................................................
5.6.3
Replacing the pulley on the ball screw upper position ....................................
5.6.4
Replacing the pulley on the ball screw lower position .....................................
5.6.5
Replacing the ball screw ...........................................................................
5.6.6
Replacing the axis-3 timing belt .................................................................
5.6.7
Replacing the axis-4 second timing belt .......................................................
5.6.8
Replacing the axis-4 timing belt .................................................................
5.6.9
Replacing the pulley pre-assembly ............................................................
5.6.10 Replacing the outer arm ...........................................................................
5.7
Motors ............................................................................................................
5.7.1
Replacing the axis-1 motor sub-assembly ....................................................
5.7.2
Replacing the axis-2 motor sub-assembly ....................................................
5.7.3
Replacing the axis-3 motor sub-assembly ....................................................
5.7.4
Replacing the axis-4 motor sub-assembly ....................................................
5.8
Gearboxes .......................................................................................................
5.8.1
Replacing the axis-1 gear unit sub-assembly ................................................
5.8.2
Replacing the axis-2 gear unit sub-assembly ................................................
6
6.1
Introduction to calibration ...................................................................................
6.1.1
Introduction and calibration terminology ......................................................
6
© Copyright 2019-2022 ABB. All rights reserved.
Product manual - IRB 910INV
3HAC068055-001 Revision: K
89
89
90
91
91
92
94
95
95
97
97
99
100
103
106
109
113
113
115
117
117
118
118
120
120
136
189
214
225
225
253
278
278
345
377
377
403
425
444
464
503
513
525
543
562
624
624
649
661
681
700
700
734
771
771
771
Advertisement
Table of Contents
Troubleshooting
