Cisco MGX 8850 Command Reference Manual page 223

Chapter 3 Equipment and Resource Provisioning
Display the general parameters for SCT 3.
MGX8850.9.AXSM.a > dspcdsct gen
+-------------------------------------------------------------------------------------------------+
Service Class Template [3] : General Parameters
+-------------------------------------------------------------------------------------------------+
| SERV-TYPE | COSB_NUM | CAC_TYPE | UPC_ENB
+-------------------------------------------------------------------------------------------------+
| VSI-SIG | 00000016 |
| CBR.1 | 00000003 |
| VBR-RT.1 | 00000004 |
| VBR-RT.2 | 00000004 |
| VBR-RT.3 | 00000004 |
| VBR-nRT.1 | 00000005 |
| VBR-nRT.2 | 00000005 |
| VBR-nRT.3 | 00000005 |
| UBR.1 | 00000006 |
| UBR.2 | 00000006 |
| ABR | 00000001 |
| CBR.2 | 00000003 |
| CBR.3 | 00000003 |
+-------------------------------------------------------------------------------------------------+
Display the Class of Service Buffer parameters for SCT 3 Note the following:
•
•
•
•
MGX8850.9.AXSM.a > dspcdsct cosb
+-----------------------------------------------------------------------------------+
|Service Class Template [03] : COSB Parameters
+-----------------------------------------------------------------------------------+
| COSB | MIN-RATE | MAX-RATE | MIN-PRIORITY | EXCESS-PRIORITY | ERS ENABLE |
+-----------------------------------------------------------------------------------+
| 0001 | 00000000 | 00000100 |
| 0002 | 00000000 | 00000100 |
| 0003 | 00000000 | 00000100 |
| 0004 | 00000000 | 00000100 |
| 0005 | 00000000 | 00000100 |
| 0006 | 00000000 | 00000100 |
| 0007 | 00000000 | 00000100 |
| 0008 | 00000000 | 00000100 |
| 0009 | 00000000 | 00000100 |
| 0010 | 00000000 | 00000100 |
| 0011 | 00000000 | 00000100 |
| 0012 | 00000000 | 00000100 |
| 0013 | 00000000 | 00000100 |
| 0014 | 00000000 | 00000100 |
| 0015 | 00000000 | 00000100 |
| 0016 | 00000000 | 00000100 |
+-----------------------------------------------------------------------------------
Release 2.0, Part Number 78-10467-04 Rev C0, October 2001
| CLP-SELEC |
B-CAC |DISABLED | 000000002 |
B-CAC |DISABLED | 000000003 |
B-CAC |DISABLED | 000000002 |
B-CAC |DISABLED | 000000001 |
B-CAC |DISABLED | 000000001 |
B-CAC |DISABLED | 000000002 |
B-CAC |DISABLED | 000000001 |
B-CAC |DISABLED | 000000001 |
LCN_CAC |DISABLED | 000000003 |
LCN_CAC |DISABLED | 000000003 | DSCD/SET-CLP |
B-CAC |DISABLED | 000000003 |
B-CAC |DISABLED | 000000001 |
B-CAC |DISABLED | 000000001 |
Min-Rate and Max-Rate do not apply in the current product.
Excess-Priority is a scheme for distributing excess bandwidth. The lowest number is the highest
priority for a connection to receive excess bandwidth. If two or more connections have equal
priority, the excess bandwidth is equally distributed between them.
Explicit Rate Stamping (ERS) applies to only ABR connections.
Cell loss ratio (CLR) is currently hard-coded, so do not attempt tot modify it through the Cisco
WAN Manager application or the CLI commands.
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
GCRA-1 | GCRA-2
DISCARD | DISCARD | DISABLED |
DISCARD | DISCARD | DISABLED |
DISCARD | DISCARD | DISABLED |
DISCARD | DISCARD | DISABLED |
DISCARD | SET-CLP | DISABLED |
DISCARD | DISCARD | DISABLED |
DISCARD | DISCARD | DISABLED |
DISCARD | SET-CLP | DISABLED |
DISCARD | DISCARD | DISABLED |
DISCARD | DISABLED |
DISCARD | DISCARD | ENABLED
DISCARD | DISCARD | DISABLED |
DISCARD | SET-CLP | DISABLED |
CLR
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
000 | DISABLE | 10^-10 |
001 | DISABLE | 10^-08 |
001 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
000 | DISABLE | 10^-06 |
Cisco MGX 8850 Routing Switch Command Reference
dspcdsct
| CI-CNTRL |
|
|
3-63