Cisco MGX 8850 Command Reference Manual page 221

Chapter 3 Equipment and Resource Provisioning
Display the Class of Service Buffer parameters for SCT 2. Note the following:
•
•
•
Cell loss ratio (CLR) is currently hard-coded, so do not attempt to modify it through the Cisco WAN
Manager application or the CLI commands.
MGX8850.1.AXSM.a > dspcdsct cosb
+-----------------------------------------------------------------------------------+
|Service Class Template [02] : COSB Parameters
+-----------------------------------------------------------------------------------+
| COSB | MIN-RATE | MAX-RATE | MIN-PRIORITY | EXCESS-PRIORITY | ERS ENABLE |
+-----------------------------------------------------------------------------------+
| 0001 | 00000000 | 00000100 |
| 0002 | 00000000 | 00000100 |
| 0003 | 00000000 | 00000100 |
| 0004 | 00000000 | 00000100 |
| 0005 | 00000000 | 00000100 |
| 0006 | 00000000 | 00000100 |
| 0007 | 00000000 | 00000100 |
| 0008 | 00000000 | 00000100 |
| 0009 | 00000000 | 00000100 |
| 0010 | 00000000 | 00000100 |
| 0011 | 00000000 | 00000100 |
| 0012 | 00000000 | 00000100 |
| 0013 | 00000000 | 00000100 |
| 0014 | 00000000 | 00000100 |
| 0015 | 00000000 | 00000100 |
| 0016 | 00000000 | 00000100 |
+-----------------------------------------------------------------------------------+
Display VC thresholds for SCT 2. Note the following:
The Scaling COSB value applies to congestion in a Class of Service Buffer: if a buffer gets congested,
this factor determines how quickly the node throttles back the rate at which cells enter the buffer.
The Scaling Log-If is a scaling factor that applies to congestion on a port: when the port gets congested,
this factor determines the rate at which the node throttles back traffic (until the port is uncongested).
MGX8850.1.AXSM.a > dspcdsct vcThr
+---------------------------------------------------------------------------------------------------------+
Service Class Template [2] : VC Threshold Parameters
+---------------------------------------------------------------------------------------------------------+
| SERV-TYPE | VC THRESH | PACKET |
| | TBL IDX
+---------------------------------------------------------------------------------------------------------+
| VSI-SIG | 225
| CBR.1 | 226
| VBR-RT.1 | 227
| VBR-RT.2 | 228
| VBR-RT.3 | 229
| VBR-nRT.1 | 230
| VBR-nRT.2 | 231
| VBR-nRT.3 | 232
| UBR.1 | 233
| UBR.2 | 234
| ABR | 235
| CBR.2 | 236
| CBR.3 | 237
Release 2.0, Part Number 78-10467-04 Rev C0, October 2001
Min-Rate and Max-Rate do not apply in the current product.
Excess-Priority is a scheme for distributing excess bandwidth. The lowest number is the highest
priority for a connection to receive excess bandwidth. If two or more connections have equal
priority, the excess bandwidth is equally distributed between them.
Explicit Rate Stamping (ERS) applies to only ABR connections.
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
000 |
MAX_CELL
| MODE | THRESH
| DSB | 0000005000 | 1000000 | 0800000 | 0600000 | 0800000 | 0000002 | 0000002 |
| DSB | 0000002500 | 1000000 | 0800000 | 0600000 | 0800000 | 0000001 | 0000001 |
| DSB | 0000005000 | 1000000 | 0800000 | 0600000 | 0800000 | 0000002 | 0000002 |
| DSB | 0000005000 | 1000000 | 0800000 | 0600000 | 0800000 | 0000002 | 0000002 |
| DSB | 0000005000 | 1000000 | 0800000 | 0600000 | 0800000 | 0000002 | 0000002 |
| DSB | 0000025000 | 1000000 | 0800000 | 0600000 | 0800000 | 0000002 | 0000002 |
| DSB | 0000025000 | 1000000 | 0800000 | 0600000 | 0800000 | 0000002 | 0000002 |
| DSB | 0000025000 | 1000000 | 0800000 | 0600000 | 0800000 | 0000002 | 0000002 |
| DSB | 0000050000 | 1000000 | 0800000 | 0600000 | 0800000 | 0000004 | 0000004 |
| DSB | 0000050000 | 1000000 | 0800000 | 0600000 | 0800000 | 0000004 | 0000004 |
| DSB | 0000050000 | 0200000 | 0800000 | 0600000 | 0800000 | 0000003 | 0000003 |
| DSB | 0000002500 | 1000000 | 0800000 | 0600000 | 0800000 | 0000001 | 0000001 |
| DSB | 0000002500 | 1000000 | 0800000 | 0600000 | 0800000 | 0000001 | 0000001 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
000 | DISABLE | 10^-10 |
001 | DISABLE | 10^-08 |
001 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
002 | DISABLE | 10^-06 |
000 | DISABLE | 10^-06 |
| EFCI | CLP_HI |
| | |
Cisco MGX 8850 Routing Switch Command Reference
CLR |
EPD0 | CLP_LO | SCALING | SCALING |
| EPD1 | COSB
dspcdsct
| Log-If |
3-61