Cisco MGX 8850 PXM45 Release Notes
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Switch
  5. MGX 8850 PXM45
  6. Release notes
Cisco MGX 8850 PXM45 Release Notes

Cisco MGX 8850 PXM45 Release Notes

Multiservice switches
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Release Notes for Cisco MGX 8850 (PXM45),
MGX 8850 (PXM1E), and MGX 8830, Software
Release 3.0.10
Contents
These release notes are part OL-2914-01 Rev. D0, July 3, 2003
About Release 3.0.10 ........................................................................................................................3
New Features and Enhancements in Release 3.0.10 ......................................................................... 4
System Requirements ........................................................................................................................8
Limitations, Restrictions, and Notes ...............................................................................................25
Corporate Headquarters:
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Copyright © 2003 Cisco Systems, Inc. All rights reserved.
Type of Release ..........................................................................................................................3
Locating Software Updates ........................................................................................................3
Release Note Document Changes ..............................................................................................3
AXSM-E Double Density .......................................................................................................... 4
PXM1E-16-T1E1 with PNNI-IMA Trunking............................................................................ 4
AXSM-32-T1E1-E with PNNI-IMA Trunking .........................................................................4
PXM-UI-S3/B Back Card ..........................................................................................................5
MCC-16-E1 ................................................................................................................................5
RBBN-16-T1E1 .........................................................................................................................5
PXM1E Online Diagnostics .......................................................................................................5
FRSM-12-T3E3 Online Diagnostics ..........................................................................................6
MGX-SRME .............................................................................................................................. 6
MGX-VISM-PR-8T1/8E1 .........................................................................................................6
Alarm Filtering........................................................................................................................... 7
Enhancements ............................................................................................................................7
Service Class Template File Information................................................................................... 7
Software/Firmware Compatibility Matrix ................................................................................. 8
Hardware Supported ................................................................................................................11
New and Modified Commands ................................................................................................ 23
Enable the FRSM, AUSM, and CESM Card cls and clr Commands ......................................24
Release 3.0.10 Limitations....................................................................................................... 25
Release 3.0.00 Limitations .......................................................................................................33
VISM Limitations .................................................................................................................... 40
RPM-PR and RPM-XF Limitations .........................................................................................41
Restrictions for Release 3.0.10 ................................................................................................41
Restrictions for Release 3.0.00 ................................................................................................ 41
Other Limitations and Restrictions .......................................................................................... 42

Advertisement

Table of Contents
loading

Related Manuals for Cisco MGX 8850 PXM45

Summary of Contents for Cisco MGX 8850 PXM45

  • Page 1: Table Of Contents

    Restrictions for Release 3.0.10 ....................41 Restrictions for Release 3.0.00 ....................41 Other Limitations and Restrictions ..................42 Corporate Headquarters: Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA Copyright © 2003 Cisco Systems, Inc. All rights reserved.
  • Page 2 Documentation CD-ROM...................... 116 Ordering Documentation .......................116 Documentation Feedback ......................116 Obtaining Technical Assistance ....................117 Cisco.com ..........................117 Technical Assistance Center ....................117 Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 3: About Release 3.0.10

    About Release 3.0.10 These release notes describe the system requirements, new features, and limitations that apply to Release 3.0.10 of the MGX 8850 and the MGX 8830 multiservice switch. These notes also contain Cisco support information. Release 3.0.00 introduced the MGX 8850 (PXM45) to both PNNI scaling via an enhanced connection count (up to 250K connections) and IP/MPLS scaling with the MGX-RPM-XF-512.

  • Page 4: New Features And Enhancements In Release 3.0.10

    It supports enhanced traffic management capabilities with per-VC/VP traffic shaping and ABR with VS/VD along with multilevel statistics. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 5: Pxm-Ui-S3/B Back Card

    Device Supported by Online Diagnostics? Atlas 0 Atlas 1 QE 0 QE 1 CBC 0 CBC 1 Disk Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 6: Frsm-12-T3E3 Online Diagnostics

    This feature provides support for the MGX-VISM-PR-8T1/8E1 card on the MGX 8830 platform, and provides the capability for voice applications in this switch. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 7: Alarm Filtering

    SCT6—Policing disabled, used for trunks. The following are checksums for the new AXSM-E SCT file: • AXSME_SCT.PORT.52.V1—Check sum = 0x199550ec = 429215980 Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 8: System Requirements

    Software/Firmware Compatibility Matrix Table 3 lists Cisco WAN or Cisco IOS products that are interoperable with Release 3.0.10. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 9 See note below. PXM1E-4-155 pxm1e_003.000.010.001_bt.fw 3.0.10 pxm1e_003.000.010.001_m30. 3.0.10 3.0.10 PXM1E-8-T3E3 (MGX 8830 chassis only) PXM1E-16-T1E PXM1E-COMBO See note below. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 10 MGX-FRSM-HS2/ frsm_vhs_VHS_BT_1.0.04.fw 1.0.04 frsm_vhs_020.000.002.000.fw 20.0.2.0 MGX-RPM-PR-256 rpm-boot-mz.122-11.T1 12.2(11)T rpm-js-mz.122-11.T1 12.2(11)T 12.2(11)T MGX-RPM-PR-512 MGX-RPM-XF-512 rpmxf-boot-mz.122-11.YP 12.2(11)Y rpmxf-js-mz.122-11.YP 12.2(11)Y 12.2(11) Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 11: Hardware Supported

    AXSM-32-T1E1-E front card, MCC-16-E1 back card, RBBN-16-T1E1 back card APS Connectors Table 6 lists MGX 8850 (PXM45) APS connectors. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 12 The PXM1E-COMBO card is also known as the PXM1E-T3E3-155 card. Note The MGX-SRME card does not need the APS-CON connector for APS. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 13 SMFLR-1-622/C 800-07411-02 SMFIR-2-622 800-05383-01 SMFLR-2-622 800-05385-01 SMFIR-2-622/B 800-07412-02 SMFLR-2-622/B 800-07413-02 MMF-4-155/C 800-07408-02 SMFIR-4-155/C 800-07108-02 SMFLR-4-155/C 800-07409-02 SMB-4-155 800-07425-02 Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 14 MGX-MMF-FE 800-03202-02 MGX-RJ45-4E/B 800-12134-01 MGX-RJ45-FE 800-02735-02 MGX-XF-UI 800-09492-01 MGX-1GE 800-18420-03 MGX-1OC12POS-IR 800-08359-05 MGX-GE-LHLX 30-1299-01 MGX-GE-SX 30-1301-01 MGX-GE-ZX 10-1439-01 Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 15 AXSM-2-622-E SMFIR-1-622/C SMFLR-1-622/C AXSM-4-622 SMFIR-2-622 SMFLR-2-622 AXSM-4-622/B SMFIR-2-622/B SMFLR-2-622/B AXSM-8-155-E SMB-4-155 MMF-4-155/C SMFIR-4-155/C SMFLR-4-155/C AXSM-16-155 MMF-8-155-MT SMFIR-8-155-LC SMFLR-8-155-LC Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 16 MGX 8850 (PXM1E) Product IDs and Card Types Table 11 contains Product IDs, 800 part numbers, and revision levels for the MGX 8850 (PXM1E). Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 17 MGX-RJ45-FE 800-02735-02 MGX-AUSM-8T1/B 800-04809-01 MGX-AUSM-8E1/B 800-04810-01 AX-CESM-8E1 800-02751-02 AX-CESM-8T1 800-02750-02 MGX-CESM-8T1/B 800-08613-02 AX-FRSM-8T1 800-02437-04 AX-FRSM-8E1 800-02438-04 AX-FRSM-8T1-C 800-02461-04 Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 18 SMFIR-4-155/C SMFLR-4-155/C PXM-UI-S3/B — PXM1E-8-T3E3 SMB-8-T3 — SMB-8-E3 — PXM-UI-S3/B — PXM1E-16-T1E1 PXM-UI-S3/B — MCC-16-E1 — RBBN-16-T1E1 — Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 19 AX-SMB-8E1 — AX-R-SMB-8E1 — AX-RJ48-8E1 — AX-R-RJ48-8E1 — MGX-CESM-8T1/B AX-RJ48-8T1 — AX-R-RJ48-8T1 — AX-FRSM-8T1 AX-RJ48-8T1 — AX-R-RJ48-8T1 — Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 20 MMF-4-155/C 800-07408-02 SMFIR-4-155/C 800-07108-02 SMFLR-4-155/C 800-07409-02 PXM-UI-S3/B 800-21557-01 SMB-8-T3 800-05029-02 SMB-8-E3 800-04093-02 MGX-T3E3-155 800-18698-02 MMF-1-155-SFP 10-1308-01 Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 21 1. These cards are required only if you need modular optics with the PXM1E-COMBO back card. 2. R means this is a redundant card. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 22 MGX-AUSM-8T1/B AX-RJ48-8T1 — AX-R-RJ48-8T1 — AX-RJ48-8E1 — AX-R-RJ48-8E1 — MGX-AUSM-8E1/B AX-SMB-8E1 — AX-R-SMB-8E1 — AX-RJ48-8E1 — AX-R-RJ48-8E1 — Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 23: New And Modified Commands

    The PXM1E-COMBO card is also known as the PXM1E-T3E3-155 card. Note New and Modified Commands Commands are described in detail in the “Cisco MGX 8830, MGX 8850 (PXM45 and PXM1E), and MGX 8950 Command Reference, Release 3” located at this URL: http://www.cisco.com/univercd/cc/td/doc/product/wanbu/8850px45/release3/cmdref/mgx3.pdf Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10...

  • Page 24: Enable The Frsm, Ausm, And Cesm Card Cls And Clr Commands

    PXM1E card before they can operate on a service module card. Complete the following steps to enable the cls and clr commands on a PXM1E card: Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 25: Limitations, Restrictions, And Notes

    Any changes in the FE IMA links in this group can cause the NE IMA group to restart. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 26 The port number in the pnport (shelf.slot:subslot.port:subport) could be a random number. The user should not interpret this number as line or IMA group number. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 27 – cnfimagrp – – upimagrp – dnimagrp – rstrtimagrp – addimalnk – clrimadelay – startimalnktst – cnfimalnktst Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 28 Init (I) state. Only messages logged in either the Active (A) or Standby (S) states are valid. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 29 With the AXSM-E double density feature, the total bandwidth supported by each Service Module • without blocking is 622 Mbps. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 30 (page 246, point b.1.2 in the ATMF PNNI specification). This higher level crankback is translated to a blocked node of the logical group node and so the source node processing this Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 31 Clocking Limitations The clock sources will be requalified when auto-revertive mode is changed using the cnfclksrc • command. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 32 (refer to caveat CSCdx30282). Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 33: Release 3.0.00 Limitations

    Only SPVCs and SPVPs are supported on narrow band service modules. SVCs are not supported on • NBSM. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 34 The PXM1E with a UI-S3 card will drop up to 70 percent of outgoing Ethernet packets to specific • switches. Use an approved Cisco hub/switch. This only applies to packets sent on the UI-S3 Ethernet interface. Known incompatible hubs are HP8000ProCurve and Netgear FS108.
  • Page 35 C: drive and the configuration of MGX-RPM-PR-256/512 and MGX-RPM-XF-512 cards in the E: drive. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 36 Path trace will not have the accurate information when there is a crankback on the connect path. • Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 37 The tstdelay command is not be available at the slave end of a single-ended SPVC on a switch. • Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 38 Due to differences in physical port numbering, non-Cisco nodes can only be the terminating nodes • in a preferred route. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 39 Suppose a root clock source is configured on NBSM which is in redundant configuration. If a switchover of the NBSM is done there might be loss of clocking for some time. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 40: Vism Limitations

    CBR/ABR traffic is expected (refer to caveat CSCdw63829). VISM Limitations For details on VISM limitations, refer to the Release Notes for Cisco Voice Interworking Service Module Release 3.1(0). These release notes are available online at the following location: http://www.cisco.com/univercd/cc/td/doc/product/wanbu/index.htm...

  • Page 41: Rpm-Pr And Rpm-Xf Limitations

    AXSM Op B and it is not required to issued the enableaxsmbaps command. The command has the following syntax: enableaxsmbaps <primary | secondary slot> Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 42: Other Limitations And Restrictions

    PXM1E). After using the clrallcnf command, you must clean up old SCT files (refer to caveat CSCdw80282). • Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 43: Limitations And Restrictions For 2.1.X

    PXM will not go to the standby ready state until one or both of the two AXSM cards are in the active ready state. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 44 If link 2 is up, if you use a rteopt command on Node A to obtain the new route, and the new path selected has a cost of 3000. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 45: Important Notes

    SPVC connection. However, the final software confirmation for available bandwidth may be rejected because there is no bandwidth available. If this problem occurs, the system will recover Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 46: Aps Management Information

    To recover, either perform a lockout of Protection line and Clear from the far end or perform delete APS for the line, then add the APS line back. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 47 Enter the dspapslns command to verify APS configuration. If the working and protection lines show OK, both lines are receiving signals from the remote note. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 48 Backcard Backcard Backcard Tx Rx Tx Rx Protection line Working line Standby line Active line Signal Physical line Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 49 M8xx0_LA.1.AXSM.a > cnfapsln -w 1.1.1 -rv 2 Table 18 describes the configurable parameters for the cnfapsln command. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 50 If you want to manually switch from one line to another, enter the switchapsln <bay> <line> <switchOption> <service switch> command, as shown in the following example: Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 51 The standby card always displays the status of the inactive line. If only one APS line fails, the line • failure LED is always displayed on the standby front card. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 52 APS pair are bad. Use Table 20 to help you determine which APS line is not functioning properly. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 53 APS lines OK. All lines in lower bay only. Upper bay Suspect bad lower bay back card. APS lines OK. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 54: Installing And Upgrading To Release 3.0.10

    Manual clocking may latch twice when upgrading the PXM45 controller cards from Release 2.1.x to Release 3.0.00 and higher. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 55: Installation And Upgrade Procedures

    • “MGX 8830 Open Caveats in Release 3.0.10” • “Status of MGX 8830 Caveats Found in Previous Releases” Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 56 However, after "cc" from pxm slot 25 is active and 27 standby. Workaround: Unknown. Table 23 describes the Severity 2 open caveats for MGX 8830 Release 3.0.10. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 57 BYTES 98% PIR 1500 BYTES 98% PIR 1000 BYTES 98% PIR 512 BYTES 97% PIR 256 BYTES 89%PIR 128 BYTES 89%PIR 64 BYTES 68%PIR Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 58 0x10005 the owner task "0x200bf" called: - CpiToAppCreateMsg+0xac - ssiIpcBufferCopy+0x6c Conditions: On a PXM1E node that has been idle for more than 6+ hours. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 59 All PNNI links go down, connections in fail state. Data traffic stops. Standby card resets after some time. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 60 Symptom: Standby PXM1E combo card CC dropped into idtmon while loading runtime image in backup boot. Conditions: Power cycle. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 61 OK. PXM1E node is acting as a PGL for the network. Last fail cause does not specify the error. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 62 Workaround: See CLI for admin state. Table 24 describes the Severity 3 open caveats for MGX 8830 Release 3.0.10. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 63 Symptom: dspcd shows lower back card empty for a full height back card. Conditions: None Workaround: None. Not service impacting. Display issue. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 64 AUSM when a stream of RM cells at 480 cps is generated by the test-set: Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 65 LOS from this line doesn't clear unlockable situation from the clock Workaround: Unknown. CSCdy66033 Hardware: pxm1e Symptom: Connections fails and doesn’t route Conditions: MGX8830, MGX8850 Workaround: Under investigation Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 66 LOS on it's trunk. After few seconds later the primary clock again went through the requalification and became active. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 67 PXM1E does not display port/switch sid CSCdw71075 SRM allows ds3linecoding to be set to HDB3 on j Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 68 Memory corruption on FRSM - indicate no channel av. CSCdx94710 REG3.0: PXM1E: Remove 4 port OC3 backcard, outage. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 69: Mgx 8850 Caveats

    MGX 8850 Open Caveats in Release 3.0.10 Table 27 lists the Severity 1 open caveats for the MGX 8850 Release 3.0.10 software. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 70 (AXSME_SCT.CARD.5) or change the CosB Max thresholds of all CosBs to be less than 300,000 in the SCT file. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 71 Condition: After a burnboot slot #8 and switchcc was executed on the shelf. Workaround: None. CSCdy81930 Hardware:axsm1b_oc12 Symptom: Port failed for over 9 minutes. Condition: Unknown. Workaround: None. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 72 Symptom: Core dump occurred for standby AXSME OC3 card though no activities. Conditions: AXSMEOC3 with standby card. Workaround: Unknown. CSCdw41209 Hardware: ausm-8t1e1 Symptom: Conditions: Workaround: Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 73 Conditions: Active PXM1E show critical card alarms Workaround: Cause the active PXM1E to be reset (switchcc or resetcd) Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 74 Hardware: pxm1e Symptom: tOam task was leaking memory in IPC buffer ids 0x10002 and 0x10003. Conditions: Unknown. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 75 RPM with the error message "% Transmit to PXM Timed out" Workaround: None. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 76 0x10005 the owner task "0x200bf" called: - CpiToAppCreateMsg+0xac - ssiIpcBufferCopy+0x6c Conditions: On a PXM1E node that has been idle for more than 6+ hours. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 77 Symptom: Switch dsplncnt for AXSME does not match FTP file on CWM. Conditions: AXSME_8OC3 card, checking INGRESS CLP0/1 Line Count Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 78 All PNNI links go down, connections in fail state. Data traffic stops. Standby card resets after some time. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 79 PXM. But after the another test failed on the newly standby PXM, dspdiagerr removed the previous message and did not update with new failure message. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 80 Symptom: XBAR alarms present on the new PXM45b Conditions: After running the sysFlashBootBurn command to upgrade the shelf. Workaround: None. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 81 VCI and other invalid attributes. Conditions: Executing dspcon with an invalid VCI to display the connection. Workaround: None. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 82 CC's clock remained primary and it never got re-qualified. Conditions: remove the standby CC's tBC Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 83 Symptom: LOA yields inconsistent active clock state in 2 pxm1e nodes. Conditions: Create an LOA on 2 pxm1e nodes. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 84 Symptom: AXSM port (with APS) went down after runrev was executed on AXSM. Conditions: One of the APS lines was in SF. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 85 Symptom: Some AXSM cards in a node were running default SCTs. Conditions: System had gone through a reset Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 86 TUG3 #2 and #3 groups. Also RDV-V alarm is received in TUG3 #2, #2 group links. The RDI-V alarm is observed on the external Mux (OPM STM1). Workaround: None. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 87 Condition: This happens only when the SNMP request is for a RPM-XF card and usually when the card has just come up. Workaround: None. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 88 Symptom: MGX45 CLI Reference Manual needs updated. Conditions: 4 new commands missing out of the manual. Workaround: None. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 89 Workaround: The system will allow the user to configure port and card level SCTs even though the display does not show it. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 90 Symptom: dspcd shows lower back card empty for a full height back card. Conditions: None Workaround: None. Not service impacting. Display issue. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 91 Workaround: Use delcon for each individual PVC until a better method is developed see PXM release notes for description of CLI commands delcon and delcons usage. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 92 Symptom: S1 byte for Synchronization Status Messaging not implemented properly. Conditions: On the AXSMB/OC12, and the AXSMB/STM1 Workaround: None. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 93 PXM45 re-learn the route to pxm1 clears this issue. This can be done by initiating a telnet from PXM45 CLI to pxm1 Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 94 Conditions: Non-native standby PXM disk is inserted and before the card could come up to standby state, the active PXM resets. Workaround: None. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 95 Conditions: Workaround: CSCdy72707 Hardware: pxm45 Symptom: Unknown. Conditions: Unknown. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 96 Symptom: PNNI ports went into down in progress and SPVCs failed. Condition: Customer was executing Fault Insertion case "CBC in reset mode" on active AXSM. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 97 Symptom: Card with fault inserted came up as standby. Condition: Customer executed HUMVEE to SPEEDUP PLD UTOPIA 3 parity error fault insertion test cases. Workaround: Unknown. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 98 Severity 1; closed. Fixed in Release 3.0.10. Hardware: PXM1E CSCdx57063 Severity 1; closed. Fixed in Release 3.0.10. Hardware: PXM1E Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 99 Severity 2; closed. Fixed in Release 3.0.10. Hardware: FRSM-12-T3E3 CSCdx54330 Severity 2; closed. Fixed in Release 3.0.10. Hardware: FRSM-12-T3E3 Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 100 The bug was fixed by design changes made for 3.0.00. Hardware: AXSMB OC-12 CSCdx79195 Severity 2; closed. Fixed in Release 3.0.10. Hardware: PXM45 Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 101 Description CSCdt70323 Change PXM burnboot process to not require console CSCdv43250 DLS: no maximum login attempts to node Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 102 APS-B: Inter, AXSM/B in OpB mode after upgrade fro CSCdx07103 cannot change ds3 lines to e3 in combo cd when all Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 103 REG3.0: SSCOP PDU corruption causes conns. to be u CSCdx49157 Unable to change SSCOP PCR after changing from def Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 104 CSCdx71109 FRSM12:After multiple switchcc, LCN for endpoints CSCdx71649 CESM pnports down on PXM1E but ports active on CES Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 105 Need mechanism to resynch port status between PXM CSCdy06992 clean up errors logged by pcema if get next on ifT Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 106 SwitchCC caused due to mainProc1 getting killed unexpectedly CSCdy59372 CPU utilization hit 0% IDLE due to pnCcb, when connections r Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 107: Known Route Processor Module Or Mpls Caveats

    APS switch Known Route Processor Module or MPLS Caveats For information about caveats with the RPM-PR or RPM/B card, refer to Release Notes for Cisco MGX Route Processor Module (RPM/B and RPM-PR) for MGX Release 1.2.11 and MGX Release 3.

  • Page 108: Documentation

    The following Cisco publications contain additional information related to the operation of this product and associated equipment in a Cisco WAN switching network. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 109 When connected to a PNNI network, each BPX 8600 series switch requires a SES for PNNI route processing. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 110 When connected to a PNNI network, each BPX 8600 series switch requires a SES for PNNI route processing. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 111 The product documentation for the installation and operation of the Service Expansion Shelf (SES) PNNI Controller is listed in Table Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 112 (RPM-PR) in the MGX 8830 Release 3 switch. Also provides troubleshooting, maintenance, and basic Cisco IOS configuration information. (For RPM-PR software configuration information only.) Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 113 The product documentation for the installation and operation of the MGX 8850 (PXM1) Multiservice Switch is listed in Table Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...
  • Page 114 Describes how to install and configure VISM in several MGX 8000 Series switches. This guide is available online only. Release 3 Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 115: Obtaining Documentation

    3.0.10 Obtaining Documentation These sections explain how to obtain documentation from Cisco Systems. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10 OL-2914-01 Rev D0, July 3, 2003...

  • Page 116: World Wide Web

    Obtaining Documentation World Wide Web You can access the most current Cisco documentation on the World Wide Web at this URL: http://www.cisco.com Translated documentation is available at this URL: http://www.cisco.com/public/countries_languages.shtml Documentation CD-ROM Cisco documentation and additional literature are available in a Cisco Documentation CD-ROM package, which is shipped with your product.

  • Page 117: Obtaining Technical Assistance

    • will occur if service is not restored quickly. No workaround is available. The Cisco TAC resource that you choose is based on the priority of the problem and the conditions of service contracts, when applicable. Release Notes for Cisco MGX 8850 (PXM45), MGX 8850 (PXM1E), and MGX 8830, Software Release 3.0.10...
  • Page 118 CCIP, CCSP, the Cisco Arrow logo, the Cisco Powered Network mark, Cisco Unity, Follow Me Browsing, FormShare, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Aironet,...

This manual is also suitable for:

Mgx 8850 pxm1eMgx 8830

Table of Contents