Woodward easYgen-2000 Series User Manual page 95

ID Parameter
1601 Engine rated
speed
1766 Generator
rated voltage
1768 Mains rated
voltage
1781 Busbar 1 rated
voltage
1752 Gen. rated
active power
[kW]
1758 Gen. rated
react. power
[kvar]
1754 Generator
rated current
1748 Mains rated
active power
[kW]
1746 Mains rated
react. pwr.
[kvar]
1785 Mains rated
current
1858 1Ph2W voltage
measuring
37535B
CL Setting range Description
[Default]
2 500 to 4,000 Number of revolutions per minute of the engine at rated engine speed. The
rpm speed control with an ECU via J1939 CAN bus refers to this value.
[1,500 rpm]
2 50 to 650000 V This value refers to the rated voltage of the generator (generator voltage on
data plate) and is the voltage measured on the potential transformer primary.
[400 V]
The generator rated voltage is used as a reference figure for all generator
voltage related functions, which use a percentage value, like generator
voltage monitoring, breaker operation windows or the Analog Manager.
2 50 to 650000 V This value refers to the rated voltage of the mains and is the voltage meas‐
ured on the potential transformer primary.
[400 V]
The mains potential transformer primary voltage is entered in this parameter.
The mains rated voltage is used as a reference figure for all mains voltage
related functions, which use a percentage value, like mains voltage moni‐
toring, breaker operation windows or the Analog Manager.
2 50 to 650000 V This value refers to the rated voltage of busbar 1 and is the voltage measured
on the potential transformer primary.
[400 V]
If voltage measuring is configured to 1Ph 3W, the WYE voltage (VL1N) must
be entered here.
The busbar 1 potential transformer primary voltage is entered in this param‐
eter. The busbar rated voltage is used as a reference figure for all busbar
voltage related functions, which use a percentage value, like synchronization.
2 0.5 to 99999.9 This value specifies the generator real power rating, which is used as a refer‐
kW ence figure for related functions. The generator rated active power is the gen‐
erator apparent power multiplied by the generator power factor (typically
[200.0 kW]
~0.8). These values are indicated in the generator data plate (
cies" on page 94 ).
2 0.5 to 99999.9 This value specifies the generator reactive power rating, which is used as a
kvar reference figure for related functions. The generator rated reactive power also
depends on the generator values (
[200.0 kvar]
2 1 to 32000 A This value specifies the generator rated current, which is used as a reference
figure for related functions.
[300 A]
2 0.5 to 99999.9 This value specifies the mains real power rating, which is used as a reference
kW figure for related functions. The mains rated active power is a reference value
used by several monitoring and control functions (
[200.0 kW]
on page 94 ).
2 0.5 to 99999.9 This value specifies the mains reactive power rating, which is used as a refer‐
kvar ence figure for related functions.
[200.0 kvar] The mains rated reactive power is a reference value used by several moni‐
toring and control functions(
2 5 to 32000 A This value specifies the mains rated current, which is used as a reference
figure for related functions.
[300 A]
3 [Phase - The unit is configured for measuring phase-phase voltages if 1Ph 2W meas‐
phase] uring is selected.
Phase - neutral The unit is configured for measuring phase-neutral voltages if 1Ph 2W meas‐
uring is selected.
easYgen-2200/2500 | Genset Control
Configure Measurement
Ä "Dependencies" on page 94 ).
Ä "Dependencies"
Ä "Dependencies" on page 94 ).
Configuration
Ä "Dependen‐
95