Woodward easYgen-2000 Series User Manual page 18

General Information
About This Manual > Revision History
Rev. Date Editor
B 2013-03-01 GG
A 2012-04-05 TE
NEW 2012-02-03 TE
18
Changes
New device features & updates
n
Undesired breaker close for synchronization when one system is configured to 1Ph2W and
the other system to 3Ph4W: problem solved.
Manual
n New overview table for synchronization matches System A with Sytem B. Refer to
Ä Chapter 9.7.3 "Synchronization Of System A and System B" on page 604 for details.
n
LS-5 load share gareway: Setting range of Parameter
n Minor corrections
Manual
n Minor corrections
Manual
n Release
The present publication (37535) replaces the following manuals which will no longer be sup‐
ported.
n
easYgen-2200/2500 installation manual (37426)
n
easYgen-2200/2500 configuration manual (37427)
n
easYgen-2200/2500 operation manual (37428)
n easYgen-2200/2500 application manual (37429)
n
easYgen-2200/2500 interface manual (37430)
New device features & updates
Requirements: easYgen-2200/2500 genset control with software version 1.01xx or higher. The
described changes relate to the previous software version 1.00xx.
New features
n Derating of power. Refer to
details.
n Ä Chapter 4.4.2.9 "QV Monitoring" on page 149 for details.
QV monitoring. Refer to
n
Mains time-dependent voltage monitoring. Refer to
Dependent Voltage" on page 146 for details.
n
Power factor characteristic. Refer to
on page 294 for details.
n Frequency depending derating of power. Refer to
Depending Derating Of Power" on page 284 for details.
n Mains voltage increase monitoring. Refer to
on page 144 for details.
n
Change of frequency - df/dt (ROCOF). Refer to
quency" on page 151 for details.
Feature updates
n Remote control. Refer to
details. "Remote control word 3" allows 16 independent interface command bits for free
remote control.
n
Support of MTU ADEC ECU8. Refer to
for details. The setting range of "Device type" (parameter
to the entry "ADEC ECU8 MTU".
n Mains undervoltage monitoring. Refer to
& 2) ANSI# 27" on page 142 for details. The setting range of "Limit" (parameter
3004 Ä p. 143 and 3010 Ä p.
n Ä Chapter 4.5.9.1 "Engine Type" on page 229 for details. The set‐
Engine type. Refer to
ting range of "Start/stop mode logic" (parameter
"Off". This allows to completely disable the start/stop sequence.
easYgen-2200/2500 | Genset Control
5568 Ä p. 303
Ä Chapter 4.5.12.3 "Derating Of Power " on page 282 for
Ä Chapter 4.4.2.8 "Mains Time-
Ä Chapter 4.5.12.6.1 "Power Factor Characteristic"
Ä Chapter 4.5.12.4 "Frequency
Ä Chapter 4.4.2.7 "Mains Voltage Increase"
Ä Chapter 4.4.2.10 "Change Of Fre‐
Ä Chapter 9.2.3 "Additional Data Identifier" on page 527 for
Ä Chapter 4.6.2.2 "J1939 Interface" on page 318
Ä Chapter 4.4.2.6 "Mains Undervoltage (Level 1
143) has been lowered from 50 % to 45 %.
3321 Ä p.
updated.
15102 Ä p. 318) was extended
229) was extended to the entry
37535B