Co: Open-Loop Flux Control Closed-Loop Controlled Reluctance Motor; Ci: Supplementary Torque 3 / M_Suppl 3 - Siemens SINAMICS G150 Manual

p1563[0...n] CO: Mom. of inertia estimator load torque direction of rotation pos. / J_est M pos
VECTOR_G Can be changed: U, T
(J_estimator)
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: REL
Min
-340.28235E36 [Nm]
Description: Display and connector output for the monitored load torque in the positive direction of rotation.
The moment of inertia estimator estimates the load torque drawn while the speed is constant.
Dependency: Refer to: p1400, p1560, p1561
p1564[0...n] CO: Mom. of inertia estimator load torque direction of rotation neg. / J_est M neg
VECTOR_G Can be changed: U, T
(J_estimator)
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: REL
Min
-340.28235E36 [Nm]
Description: Display and connector output for the monitored load torque in the negative direction of rotation.
The moment of inertia estimator estimates the load torque drawn while the speed is constant.
Dependency: Refer to: p1400, p1560, p1561
r1568[0...5] CO: Open-loop flux control closed-loop controlled reluctance motor / Flux ctrl SRM
VECTOR_G (n/M) Can be changed: -
Data type: FloatingPoint32
P-Group: Closed-loop control
Not for motor type: ASM, PEM, REL, FEM Scaling: PERCENT
Min
- [%]
Description: Displays signals of the open-loop flux control of the closed-loop controlled reluctance motor.
Index: [0] = Setpoint before filter
[1] = Output MTPC characteristic
[2] = Lower limit at low torque
[3] = Lower limit at low speed
[4] = Upper limit from field weakening controller total
[5] = Upper limit from field weakening controller precontrol
p1569[0...n]

CI: Supplementary torque 3 / M_suppl 3

VECTOR_G (n/M) Can be changed: T
Data type: Unsigned32 / FloatingPoint32
P-Group: Functions
Not for motor type: REL
Min
-
Description: Sets the signal source for supplementary torque 3.
Dependency: Refer to: p3842
Notice: The signal input is after the torque limit (r1538, r1539). For vector drives, the signals that are entered are only limited
by the current and power limits.
Note: The signal input is preferably used to enter the friction characteristic. The friction compensation is also effective if the
speed controller output reaches its torque limits, but the current limits have still not been reached (this only applies to
vector drives).
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
Calculated: -
Dyn. index: DDS, p0180
Units group: -
Scaling: p2003
Max
340.28235E36 [Nm]
Calculated: -
Dyn. index: DDS, p0180
Units group: -
Scaling: p2003
Max
340.28235E36 [Nm]
Calculated: -
Dyn. index: -
Units group: -
Max
- [%]
Calculated: -
Dyn. index: CDS, p0170
Units group: -
Scaling: p2003
Max
-
2 Parameters
2.2 List of parameters
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0.00 [Nm]
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0.00 [Nm]
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
- [%]
Access level: 2
Func. diagram: 7010
Unit selection: -
Expert list: 1
Factory setting
3841[0]
389