Sampling Times / T_Sample; Hardware Sampling Times Still Assignable / Hw T_Samp Free; Bi: Input Signal Bit-Serially 0 / Input_Sig Bit 0 - Siemens SINAMICS G150 Manual

2 Parameters
2.2 List of parameters
[13] = Drive object number object 13
[14] = Drive object number object 14
[15] = Drive object number object 15
[16] = Drive object number object 16
[17] = Drive object number object 17
[18] = Drive object number object 18
[19] = Drive object number object 19
[20] = Drive object number object 20
[21] = Drive object number object 21
[22] = Drive object number object 22
[23] = Drive object number object 23
Notice: This parameter may only be used by qualified service personnel.
Note: If the same drive object numbers are used and if the existing drive object numbers in the system are entered
incompletely, the content of this parameter is ignored entirely. The behavior as with factory setting will then become
effective.
r7901[0...81]

Sampling times / t_sample

CU_G130_DP, Can be changed: -
CU_G130_PN,
Data type: FloatingPoint32
CU_G150_DP,
P-Group: -
CU_G150_PN
Not for motor type: -
Min
- [µs]
Description: Displays the sampling times currently present on the drive unit.
r7901[0...63]: sampling times of hardware time slices.
r7901[64...82]: sampling times of software time slices.
r7901[x] = 0 means that in the associated time slice, no methods have been registered.
Note: The basis for the software time slices is T_NRK = p7901[15].
r7903

Hardware sampling times still assignable / HW t_samp free

CU_G130_DP, Can be changed: -
CU_G130_PN,
Data type: Unsigned16
CU_G150_DP,
P-Group: -
CU_G150_PN
Not for motor type: -
Min
-
Description: Displays the number of hardware sampling times that can still be assigned.
These free sampling times can be used by OA applications such as DCC or FBLOCKS.
Note: OA: Open Architecture
p8500[0...7]

BI: Input signal bit-serially 0 / Input_sig bit 0

CU_G130_DP, Can be changed: U, T
CU_G130_PN,
Data type: Unsigned32 / Binary
CU_G150_DP,
P-Group: -
CU_G150_PN
Not for motor type: -
Min
-
Description: Sets the signal source for bit-serial input signals.
These signals are available in binector output r8510.0 ... 7 for further interconnection.
Index: [0] = To BO: r8510.0
[1] = To BO: r8510.1
[2] = To BO: r8510.2
[3] = To BO: r8510.3
[4] = To BO: r8510.4
[5] = To BO: r8510.5
[6] = To BO: r8510.6
[7] = To BO: r8510.7
746
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
- [µs]
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
List Manual (LH2), 04/2014, A5E03263479A
Access level: 4
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
- [µs]
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 2
Func. diagram: 2195
Unit selection: -
Expert list: 1
Factory setting
0
SINAMICS G130/G150