Bi: Can Status Word Bit 8 / Status Word Bit 8; Bi: Can Status Word Bit 14 / Status Word Bit 14; Bi: Can Status Word Bit 15 / Status Word Bit 15; Can Control Word - Auto Interconnection / Stw Interc Auto - Siemens SINAMICS G150 Manual

14
15
Note: Corresponds to the CANopen object 6041 hex + 800 hex * x (x: Drive number 0 ... 7).
Re bit 10:
When the ramp-function generator is activated, the interconnection from CI: p2151 = r1119 can be changed, so that
to evaluate bit 10, the setpoint can be retrieved (taken) from in front of the ramp-function generator.
Re bit 10, 12:
When braking, the two bits must indicate the same state. This is the reason that the following parameters must be set
the same:
p2161 (speed threshold value 3, for r2199.0) = p2163 (speed threshold value 4, for r2197.7)
p2150 (hysteresis speed 3, for r2199.0) = p2164 (hysteresis speed 4, for r2197.7)
p8785

BI: CAN status word bit 8 / Status word bit 8

VECTOR_G (CAN) Can be changed: T
Data type: Unsigned32 / Binary
P-Group: Communications
Not for motor type: -
Min
-
Description: Sets the signal source for bit 8 of the CANopen status word.
Dependency: Refer to: r8784
p8786

BI: CAN status word bit 14 / Status word bit 14

VECTOR_G (CAN) Can be changed: T
Data type: Unsigned32 / Binary
P-Group: Communications
Not for motor type: -
Min
-
Description: Sets the signal source for bit 14 of the CANopen status word.
Dependency: Refer to: r8784
p8787

BI: CAN status word bit 15 / Status word bit 15

VECTOR_G (CAN) Can be changed: T
Data type: Unsigned32 / Binary
P-Group: Communications
Not for motor type: -
Min
-
Description: Sets the signal source for bit 15 of the CANopen status word.
Dependency: Refer to: r8784
p8790

CAN control word - auto interconnection / STW interc auto

VECTOR_G (CAN) Can be changed: C1(3), T
Data type: Integer16
P-Group: Communications
Not for motor type: -
Min
0
Description: Sets the automatic BICO interconnection of the CANopen control word.
Value: 0:
1:
Dependency: Refer to: r2050, r2090, r2091, r2092, r2093, r8750, r8795, r8850, r8890, r8891, r8892, r8893
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
Can be freely interconnected (BI: p8786)
Can be freely interconnected (BI: p8787)
No interconn
Interconnection
Yes
Yes
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
1
2 Parameters
2.2 List of parameters
No
No
Access level: 3
Func. diagram: 9226
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: 9226
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: 9226
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
0
-
-
779