Cbe2X Subnet Mask Of Station Active / Cbe2X Sub Mask Act; Cbe2X Dhcp Mode Active / Cbe2X Dhcp Act; Cbe2X Mac Address Of Station / Cbe2X Mac Addr; Cbe2X Dap Id / Cbe2X Dap Id - Siemens SINAMICS G150 Manual

r8953[0...3]

CBE2x Subnet Mask of Station active / CBE2x Sub Mask act

CU_G130_DP Can be changed: -
(PROFINET CBE20),
Data type: Unsigned8
CU_G130_PN
P-Group: -
(PROFINET CBE20),
Not for motor type: -
CU_G150_DP
(PROFINET CBE20),
Min
CU_G150_PN
0
(PROFINET CBE20)
Description: Displays the active subnet mask for the Communication Board Ethernet 20/25 (CBE20/CBE25).
r8954

CBE2x DHCP Mode active / CBE2x DHCP act

CU_G130_DP Can be changed: -
(PROFINET CBE20),
Data type: Unsigned8
CU_G130_PN
P-Group: -
(PROFINET CBE20),
Not for motor type: -
CU_G150_DP
(PROFINET CBE20),
Min
CU_G150_PN
0
(PROFINET CBE20)
Description: Displays the active DHCP mode for the Communication Board Ethernet 20/25 (CBE20/CBE25).
Notice: When the DHCP mode is active (parameter value greater than 0), PROFINET communication via this interface is no
longer possible! However, the interface can be used by the STARTER/SCOUT commissioning tool.
Note: If value = 0:
DHCP deactivated.
If value = 2:
DHCP activated. The MAC address of this interface is used for client identification.
If value = 3:
DHCP activated. The station name of this interface is used for client identification.
r8955[0...5]

CBE2x MAC Address of Station / CBE2x MAC Addr

CU_G130_DP Can be changed: -
(PROFINET CBE20),
Data type: Unsigned8
CU_G130_PN
P-Group: -
(PROFINET CBE20),
Not for motor type: -
CU_G150_DP
(PROFINET CBE20),
Min
CU_G150_PN
0000 hex
(PROFINET CBE20)
Description: Displays the MAC address for the Communication Board Ethernet 20/25 (CBE20/CBE25).
r8959

CBE2x DAP ID / CBE2x DAP ID

CU_G130_DP Can be changed: -
(PROFINET CBE20),
Data type: Unsigned32
CU_G130_PN
P-Group: -
(PROFINET CBE20),
Not for motor type: -
CU_G150_DP
(PROFINET CBE20),
Min
CU_G150_PN
0000 hex
(PROFINET CBE20)
Description: Displays the DAP ID for PROFINET via the Communication Board Ethernet 20/25 (CBE20/CBE25).
The combination of device ID (r8909) and DAP ID (r8959) uniquely identifies a PROFINET access point.
Note: DAP ID: Device Access Point ID
DAP ID = 20007 hex: SINAMICS CBE20 V4.5
DAP ID = 20008 hex: SINAMICS CBE20 V4.6
DAP ID = 20009 hex: SINAMICS CBE20 V4.7
DAP ID = 20209 hex: SINAMICS CBE25 V4.7
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
255
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
00FF hex
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
FFFF FFFF hex
2 Parameters
2.2 List of parameters
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 3
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
831