Tm31 Digital Outputs Limit Current / Tm31 Do Limit Curr; Tb30 Digital Outputs Status / Tb30 Do Status; Tm31 Digital Outputs Status / Tm31 Do Status - Siemens SINAMICS G150 Manual

Note: Prerequisite: The DI/DO must be set as an output (p4028.11 = 1).
DI/DO: Bidirectional Digital Input/Output
p4046

TM31 digital outputs limit current / TM31 DO limit curr

TM31 Can be changed: T
Data type: Integer16
P-Group: Commands
Not for motor type: -
Min
0
Description: Sets the limit for the total output voltage of terminals X541.1, X541.2, X541.3 and X541.4 (DI/DO 8 ... 11) of Terminal
Module 31 (TM31).
Value: 0:
1:
Dependency: Refer to: p4028
Warning: Since the sum of the output currents at terminals X541.1, X541.2, X541.3 and X541.4 is limited, an overcurrent or
short circuit at one output terminal can cause a dip in the signal at the other terminals.
r4047

TB30 digital outputs status / TB30 DO status

TB30 Can be changed: -
Data type: Unsigned32
P-Group: Commands
Not for motor type: -
Min
-
Description: Displays the status of the digital outputs of the Terminal Board 30 (TB30).
Bit field: Bit
00
01
02
03
Note: Inversion using p4048 has been taken into account.
DO: Digital Output
r4047

TM31 digital outputs status / TM31 DO status

TM31 Can be changed: -
Data type: Unsigned32
P-Group: Commands
Not for motor type: -
Min
-
Description: Displays the status of the digital outputs of Terminal Module 31 (TM31).
Bit field: Bit
00
01
08
09
10
11
Note: Inversion using p4048 has been taken into account.
The setting of the DI/DO as either input or output is of no significance (p4028).
DO: Digital Output
DI/DO: Bidirectional Digital Input/Output
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
0.1 A total current limit DI/DO 8 ... 11
1.0 A total current limit DI/DO 8 ... 11
Signal name
DO 0 (X481.5)
DO 1 (X481.6)
DO 2 (X481.7)
DO 3 (X481.8)
Signal name
DO 0 (X542.1 - 3)
DO 1 (X542.4 - 6)
DI/DO 8 (X541.2)
DI/DO 9 (X541.3)
DI/DO 10 (X541.4)
DI/DO 11 (X541.5)
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
1
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
1 signal
High
High
High
High
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
1 signal
High
High
High
High
High
High
2 Parameters
2.2 List of parameters
Access level: 2
Func. diagram: 9560
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 1
Func. diagram: 9102
Unit selection: -
Expert list: 1
Factory setting
-
0 signal
Low
Low
Low
Low
Access level: 1
Func. diagram: 9556, 9560,
9562
Unit selection: -
Expert list: 1
Factory setting
-
0 signal
Low
Low
Low
Low
Low
Low
FP
-
-
-
-
FP
-
-
-
-
-
-
605