Tb30 Analog Outputs Characteristic Value X2 / Tb30 Ao Char X2; Tm31 Analog Outputs Characteristic Value X2 / Tm31 Ao Char X2; Tb30 Analog Outputs Characteristic Value Y2 / Tb30 Ao Char Y2; Tm31 Analog Outputs Characteristic Value Y2 / Tm31 Ao Char Y2 - Siemens SINAMICS G150 Manual

p4079[0...1]

TB30 analog outputs characteristic value x2 / TB30 AO char x2

TB30 Can be changed: U, T
Data type: FloatingPoint32
P-Group: Terminals
Not for motor type: -
Min
-1000.00 [%]
Description: Sets the scaling characteristic for the analog outputs of Terminal Board 30 (TB30).
The scaling characteristic for the analog outputs is defined using 2 points.
This parameter specifies the x coordinate (percentage) of the 2nd value pair of the characteristic.
Index: [0] = AO 0 (X482.5/X482.6)
[1] = AO 1 (X482.7/X482.8)
Note: The parameters for the characteristic do not have a limiting effect.
p4079[0...1]

TM31 analog outputs characteristic value x2 / TM31 AO char x2

TM31 Can be changed: U, T
Data type: FloatingPoint32
P-Group: Terminals
Not for motor type: -
Min
-1000.00 [%]
Description: Sets the scaling characteristic for the analog outputs of Terminal Module 31 (TM31).
The scaling characteristic for the analog outputs is defined using 2 points.
This parameter specifies the x coordinate (percentage) of the 2nd value pair of the characteristic.
Index: [0] = AO 0 (X522.1, X522.2, X522.3)
[1] = AO 1 (X522.4, X522.5, X522.6)
Dependency: Refer to: r4076, p4076
Notice: This parameter is automatically overwritten when changing p4076 (type of analog outputs).
Note: The parameters for the characteristic do not have a limiting effect.
p4080[0...1]

TB30 analog outputs characteristic value y2 / TB30 AO char y2

TB30 Can be changed: U, T
Data type: FloatingPoint32
P-Group: Terminals
Not for motor type: -
Min
-11.000 [V]
Description: Sets the scaling characteristic for the analog outputs of Terminal Board 30 (TB30).
The scaling characteristic for the analog outputs is defined using 2 points.
This parameter specifies the y coordinate (output voltage in V) of the 2nd value pair of the characteristic.
Index: [0] = AO 0 (X482.5/X482.6)
[1] = AO 1 (X482.7/X482.8)
Note: The parameters for the characteristic do not have a limiting effect.
p4080[0...1]

TM31 analog outputs characteristic value y2 / TM31 AO char y2

TM31 Can be changed: U, T
Data type: FloatingPoint32
P-Group: Terminals
Not for motor type: -
Min
-20.000 [V]
Description: Sets the scaling characteristic for the analog outputs of Terminal Module 31 (TM31).
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
1000.00 [%]
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
1000.00 [%]
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
11.000 [V]
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
20.000 [V]
2 Parameters
2.2 List of parameters
Access level: 2
Func. diagram: 9106
Unit selection: -
Expert list: 1
Factory setting
100.00 [%]
Access level: 2
Func. diagram: 9572
Unit selection: -
Expert list: 1
Factory setting
100.00 [%]
Access level: 2
Func. diagram: 9106
Unit selection: -
Expert list: 1
Factory setting
10.000 [V]
Access level: 2
Func. diagram: 9572
Unit selection: -
Expert list: 1
Factory setting
10.000 [V]
619