Bi: Cu Signal Source For Terminal Di/Do 14 / Cu S_Src Di/Do 14; Bi: Cu Signal Source For Terminal Di/Do 15 / Cu S_Src Di/Do 15; Cu Digital Outputs Status / Cu Do Status - Siemens SINAMICS G150 Manual

To the terminal designation:
The first designation is valid for CU320, the second for CU310.
Notice: The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note: Prerequisite: The DI/DO must be set as an output (p0728.13 = 1).
DI/DO: Bidirectional Digital Input/Output
p0744

BI: CU signal source for terminal DI/DO 14 / CU S_src DI/DO 14

CU_G130_DP, Can be changed: U, T
CU_G130_PN,
Data type: Unsigned32 / Binary
CU_G150_DP,
P-Group: Commands
CU_G150_PN
Not for motor type: -
Min
-
Description: Sets the signal source for terminal DI/DO 14 (X132.12 / X131.4).
To the terminal designation:
The first designation is valid for CU320, the second for CU310.
Notice: The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note: Prerequisite: The DI/DO must be set as an output (p0728.14 = 1).
DI/DO: Bidirectional Digital Input/Output
p0745

BI: CU signal source for terminal DI/DO 15 / CU S_src DI/DO 15

CU_G130_DP, Can be changed: U, T
CU_G130_PN,
Data type: Unsigned32 / Binary
CU_G150_DP,
P-Group: Commands
CU_G150_PN
Not for motor type: -
Min
-
Description: Sets the signal source for terminal DI/DO 15 (X132.13 / X131.5you).
To the terminal designation:
The first designation is valid for CU320, the second for CU310.
Notice: The parameter may be protected as a result of p0922 or p2079 and cannot be changed.
Note: Prerequisite: The DI/DO must be set as an output (p0728.15 = 1).
DI/DO: Bidirectional Digital Input/Output
r0747

CU digital outputs status / CU DO status

CU_G130_DP, Can be changed: -
CU_G130_PN,
Data type: Unsigned32
CU_G150_DP,
CU_G150_PN
P-Group: Commands
Not for motor type: -
Min
-
Description: Displays the status of digital outputs.
Bit field: Bit
08
09
10
11
12
13
14
15
Notice: To the terminal designation:
The first designation is valid for CU320, the second for CU310.
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
Signal name
DI/DO 8 (X122.9/X121.7)
DI/DO 9 (X122.10/X121.8)
DI/DO 10 (X122.12/X121.10)
DI/DO 11 (X122.13/X121.11)
DI/DO 12 (X132.9/X131.1)
DI/DO 13 (X132.10/X131.2)
DI/DO 14 (X132.12/X131.4)
DI/DO 15 (X132.13/X131.5)
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
-
1 signal
High
High
High
High
High
High
High
High
2 Parameters
2.2 List of parameters
Access level: 1
Func. diagram: 2133
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 1
Func. diagram: 2119, 2133
Unit selection: -
Expert list: 1
Factory setting
0
Access level: 1
Func. diagram: 2130, 2131,
2132, 2133
Unit selection: -
Expert list: 1
Factory setting
-
0 signal
Low
Low
Low
Low
Low
Low
Low
Low
FP
-
-
-
-
-
-
-
-
241