Co: Tm31 Analog Inputs Actual Value In Percent / Tm31 Ai Value In %; Tb30 Analog Inputs Type / Tb30 Ai Type; Tm31 Analog Inputs Type / Tm31 Ai Type - Siemens SINAMICS G150 Manual

2 Parameters
2.2 List of parameters
r4055[0...1]

CO: TM31 analog inputs actual value in percent / TM31 AI value in %

TM31 Can be changed: -
Data type: FloatingPoint32
P-Group: Terminals
Not for motor type: -
Min
- [%]
Description: Displays the currently referred input value of the analog inputs of Terminal Module 31 (TM31).
When interconnected, the signals are referred to the reference quantities p200x and p205x.
Index: [0] = AI 0 (X521.1/X521.2, S5.0)
[1] = AI 1 (X521.3/X521.4, S5.1)
Note: AI: Analog Input
r4056[0...1]

TB30 analog inputs type / TB30 AI type

TB30 Can be changed: -
Data type: Integer16
P-Group: Terminals
Not for motor type: -
Min
4
Description: Displays the type of analog inputs.
Value: 4:
Index: [0] = AI 0 (X482.1/X482.2)
[1] = AI 1 (X482.3/X482.4)
p4056[0...1]

TM31 analog inputs type / TM31 AI type

TM31 Can be changed: U, T
Data type: Integer16
P-Group: Terminals
Not for motor type: -
Min
0
Description: Sets the type of analog inputs of Terminal Module 31 (TM31).
p4056[x] = 0, 4 correspond to a voltage input (r4052, p4057, p4059 are displayed in V).
p4056[x] = 2, 3, 5 correspond to a current input (r4052, p4057, p4059 are displayed in mA).
In addition, the associated switch S5 must be appropriately set.
AI 0: S5.0 = V --> voltage input, S5.0 = I --> current input (burden resistor = 250 Ohm)
AI 1: S5.1 = V --> voltage input, S5.1 = I --> current input (burden resistor = 250 Ohm)
Value: 0:
2:
3:
4:
5:
Index: [0] = AI 0 (X521.1/X521.2, S5.0)
[1] = AI 1 (X521.3/X521.4, S5.1)
Warning: The maximum voltage difference between the analog input terminals AI+, AI- and the ground of the TM31 (X520.6,
X530.3) may not exceed 35 V.
For operation with the load resistor switched in, the voltage between the differential inputs AI+ and AI- may not
exceed 15 V or the impressed current of 60 mA; if this is not carefully observed, the input will be damaged.
Notice: For operation as a voltage input/current input, switch S5.0 or S5.1 must be appropriately set.
608
Bipolar voltage input (-10 V ... +10 V)
Unipolar voltage input (0 V ... +10 V)
Unipolar current input (0 mA ... +20 mA)
Unipolar current input monitored (+4 mA to +20 mA)
Bipolar voltage input (-10 V ... +10 V)
Bipolar current input (-20 mA to +20 mA)
Calculated: -
Dyn. index: -
Units group: -
Scaling: PERCENT
Max
- [%]
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
4
Calculated: -
Dyn. index: -
Units group: -
Scaling: -
Max
5
List Manual (LH2), 04/2014, A5E03263479A
Access level: 1
Func. diagram: 9549, 9566,
9568
Unit selection: -
Expert list: 1
Factory setting
- [%]
Access level: 1
Func. diagram: -
Unit selection: -
Expert list: 1
Factory setting
-
Access level: 1
Func. diagram: 9566, 9568
Unit selection: -
Expert list: 1
Factory setting
4
SINAMICS G130/G150