Intel 6 SERIES CHIPSET - DATASHEET 01-2011 Datasheet page 303

Electrical Characteristics
Table 8-7. DC Characteristic Input Signal Association (Sheet 2 of 2)
Symbol
VIH11/VIL11
VIH12 (Absolute
Maximum) / VIL12
(Absolute Minimum) /
Vclk_in_cross(abs)
VIH13/VIL13
VIH14/VIL14
VIH15/VIL15
VIH16/VIL16
VIH_CL/VIL_CL
VDI / VCM / VSE
(5V Tolerant)
V HSSQ / V HSDSC /
V HSCM
(5V Tolerant)
VIH_HDA / VIL_HDA
VIH_FDI/VIL_FDI
VAUX-Diff-P-P
VIH_XTAL25/
VIL_XTAL25
VIMIN17-Gen3i/
VIMAX17-Gen3i
NOTES:
1. V
DI
2. Includes VDI range
3. Applies to Low-Speed/High-Speed USB
4. PCI Express mVdiff p-p = 2*|PETp[x] – PETn[x]|
5. SATA Vdiff, RX (VIMAX10/MIN10) is measured at the SATA connector on the receiver side
(generally, the motherboard connector), where SATA mVdiff p-p = 2*|SATA[x]RXP –
SATA[x]RXN|
6. VccRTC is the voltage applied to the VccRTC well of the PCH. When the system is in a G3
state, this is generally supplied by the coin cell battery, but for S5 and greater, this is
generally VccSus3_3.
7. CL_Vref = 0.12*(VccSus3_3)
8. This is an AC characteristic that represents transient values for these signals.
9. Applies to High-Speed USB 2.0.
Datasheet
Intel High Definition Audio Signals: HDA_SDIN[3:0] (3.3V Mode)
Strap Signals: HDA_SDO, HDA_SYNC (Strap purposes only)
GPIO Signals: GPIO13
NOTE: See VIL_HDA/VIH_HDA for High Definition Audio Low Voltage Mode
Clock Signals: CLKIN_DMI_[P,N], CLKIN_DOT96[P,N], CLKIN_SATA_[P,N]]
Miscellaneous Signals: RTCRST#
Power Management Signals: PWROK, RSMRST#, DPWROK
System Management Signals: INTRUDER#
Miscellaneous Signals: INTVRMEN, SRTCRST#
Digital Display Control Signals: CRT_DDC_CLK, CRT_DDC_DATA
SDVO_CTRLCLK, SDVO_CTRLDATA, DDPC_CTRLCLK, DDPC_CTRLDATA,
DDPD_CTRLCLK, DDPD_CTRLDATA
Mobile only: L_BKLTEN, L_BKLTCTL, L_DDC_CLK, L_DDC_DATA
Processor Interface: RCIN#
Power Management Signals: SYS_PWROK, APWROK
Controller Link: CL_CLK1, CL_DATA1
USB Signals: USBP[13:0][P,N] (Low-speed and Full-speed)
USB Signals: USBP[13:0][P,N] (in High-speed Mode)
®
Intel High Definition Audio Signals: HDA_SDIN[3:0]
Strap Signals: HDA_SDO, HDA_SYNC (Strap purposes only)
NOTE: Only applies when running in Low Voltage Mode (1.5 V)
®
Intel Flexible Display Interface Signals: FDI_RX[P,N][7:0]
Digital Display Port Aux Signal (Receiving Side): DDP[D:B]_AUX[P,N]
25MHz Crystal Input
XTAL25_IN
SATA Signals: SATA[5:0]RX[P,N] (6.0 Gb/s internal SATA)
= | USBPx[P] – USBPx[N]
Associated Signals
303