Siemens SINAMICS G150 Manual page 1003

p1139[0...n]
p1140[0...n]
p1141[0...n]
p1142[0...n]
p1143[0...n]
p1144[0...n]
p1155[0...n]
p1160[0...n]
p1201[0...n]
p1230[0...n]
p1235[0...n]
p1330[0...n]
p1356[0...n]
p1437[0...n]
p1440[0...n]
p1455[0...n]
p1466[0...n]
p1475[0...n]
p1476[0...n]
p1477[0...n]
p1478[0...n]
p1479[0...n]
p1486[0...n]
p1492[0...n]
p1495[0...n]
p1497[0...n]
p1500[0...n]
p1501[0...n]
p1502[0...n]
p1503[0...n]
p1511[0...n]
p1512[0...n]
p1513[0...n]
p1522[0...n]
p1523[0...n]
p1528[0...n]
p1529[0...n]
p1540[0...n]
p1541[0...n]
p1545[0...n]
p1551[0...n]
p1552[0...n]
p1554[0...n]
p1555[0...n]
p1569[0...n]
p1571[0...n]
p1640[0...n]
p2103[0...n]
p2104[0...n]
p2105[0...n]
p2106[0...n]
p2107[0...n]
p2108[0...n]
p2112[0...n]
p2116[0...n]
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A
CI: Ramp-function generator ramp-down time scaling / RFG t_RD scal
BI: Enable ramp-function generator/inhibit ramp-function generator / RFG enable
BI: Continue ramp-function generator/freeze ramp-function generator / Continue RFG
BI: Enable setpoint/inhibit setpoint / Setpoint enable
BI: Ramp-function generator, accept setting value / RFG accept set v
CI: Ramp-function generator setting value / RFG setting value
CI: Speed controller speed setpoint 1 / n_ctrl n_set 1
CI: Speed controller speed setpoint 2 / n_ctrl n_set 2
BI: Flying restart enable signal source / Fly_res enab S_src
BI: Armature short-circuit / DC braking activation / ASC/DCBRK act
BI: External armature short-circuit contactor feedback signal / ASC ext feedback
CI: U/f control independent voltage setpoint / Uf U_set independ.
CI: U/f control angular setpoint / Uf ang setpoint
CI: Speed controller reference model I component input / n_ctrRefMod I_comp
CI: Speed controller speed actual value / n_ctrl n_act
CI: Speed controller P gain adaptation signal / n_ctr adapt_sig Kp
CI: Speed controller P-gain scaling / n_ctrl Kp scal
CI: Speed controller torque setting value for motor holding brake / n_ctrl M_sv MHB
BI: Speed controller hold integrator / n_ctrl integ stop
BI: Speed controller set integrator value / n_ctrl integ set
CI: Speed controller integrator setting value / n_ctr integ_setVal
CI: Speed controller integrator setting value scaling / n_ctrl I_val scal
CI: Droop compensation torque / Droop M_comp
BI: Droop feedback enable / Droop enable
CI: Acceleration pre-control / a_prectrl
CI: Moment of inertia scaling signal source / M_inert scal s_src
Macro Connector Inputs (CI) for torque setpoints / Macro CI M_set
BI: Change over between closed-loop speed/torque control / Changeov n/M_ctrl
BI: Freeze moment of inertia estimator / J_estim freeze
CI: Torque setpoint / M_set
CI: Supplementary torque 1 / M_suppl 1
CI: Supplementary torque 1 scaling / M_suppl 1 scal
CI: Supplementary torque 2 / M_suppl 2
CI: Torque limit upper / M_max upper
CI: Torque limit lower / M_max lower
CI: Torque limit upper scaling / M_max upper scal
CI: Torque limit lower scaling / M_max lower scal
CI: Torque limit speed controller upper scaling / M_max n-ctr upScal
CI: Torque limit. speed controller lower scaling / M_max nctr lowScal
BI: Activates travel to a fixed stop / TfS activation
BI: Torque limit variable/fixed signal source / M_lim var/fixS_src
CI: Torque limit upper scaling without offset / M_max up w/o offs
CI: Torque limit lower scaling without offset / M_max low w/o offs
CI: Power limit / P_max
CI: Supplementary torque 3 / M_suppl 3
CI: Supplementary flux setpoint / Suppl flux setp
CI: Excitation current actual value signal source / I_exc_ActVal S_src
BI: 1. Acknowledge faults / 1. Acknowledge
BI: 2. Acknowledge faults / 2. Acknowledge
BI: 3. Acknowledge faults / 3. Acknowledge
BI: External fault 1 / External fault 1
BI: External fault 2 / External fault 2
BI: External fault 3 / External fault 3
BI: External alarm 1 / External alarm 1
BI: External alarm 2 / External alarm 2
2 Parameters
2.3 Parameters for data sets
1003