Parameters For Encoder Data Sets (Eds) - Siemens SINAMICS G150 Manual

2 Parameters
2.3 Parameters for data sets
2.3.3

Parameters for encoder data sets (EDS)

The following list contains the parameters that are dependent on the encoder data sets.
Product: SINAMICS G130/G150, Version: 4702900, Language: eng, Type: EDS
p0141[0...n]
p0142[0...n]
p0144[0...n]
p0145[0...n]
r0146[0...n]
r0147[0...n]
r0148[0...n]
p0400[0...n]
p0401[0...n]
p0402[0...n]
p0404[0...n]
p0405[0...n]
p0407[0...n]
p0408[0...n]
p0410[0...n]
p0411[0...n]
p0412[0...n]
p0413[0...n]
p0414[0...n]
p0415[0...n]
p0416[0...n]
p0417[0...n]
p0418[0...n]
p0419[0...n]
p0420[0...n]
p0421[0...n]
p0422[0...n]
p0423[0...n]
p0424[0...n]
p0425[0...n]
p0426[0...n]
p0427[0...n]
p0428[0...n]
p0429[0...n]
p0430[0...n]
p0431[0...n]
p0432[0...n]
p0433[0...n]
p0434[0...n]
p0435[0...n]
p0436[0...n]
p0437[0...n]
p0438[0...n]
p0439[0...n]
p0440[0...n]
p0441[0...n]
p0442[0...n]
p0443[0...n]
p0444[0...n]
p0445[0...n]
p0446[0...n]
1012
Encoder interface (Sensor Module) component number / Enc_interf comp_no
Encoder component number / Encoder comp_no
Sensor Module detection via LED / SM detection LED
Activate/de-activate encoder interface / Enc_intf act/deact
Encoder interface active/inactive / Enc_intf act/inact
Sensor Module EEPROM data version / SM EEPROM version
Sensor Module firmware version / SM FW version
Encoder type selection / Enc_typ sel
Encoder type OEM selection / Enc type OEM sel
Gearbox type selection / Gearbox type sel
Encoder configuration effective / Enc_config eff
Square-wave encoder track A/B / Sq-wave enc A/B
Linear encoder grid division / Enc grid div
Rotary encoder pulse number / Rot enc pulse No.
Encoder inversion actual value / Enc inv act value
Measuring gear configuration / Meas gear config
Measuring gear absolute encoder rotary revolutions virtual / Abs rot rev
Measuring gear position tracking tolerance window / Pos track window
Redundant coarse position value relevant bits (identified) / Relevant bits
Gx_XIST1 Coarse position safe most significant bit (identified) / Gx_XIST1 safe MSB
Non safety-relevant meas. steps position value POS1 (detected) / nsrPos1
Encoder safety comparison algorithm (detected) / Safety comp_algo
Fine resolution Gx_XIST1 (in bits) / Enc fine Gx_XIST1
Fine resolution absolute value Gx_XIST2 (in bits) / Enc fine Gx_XIST2
Encoder connection / Enc_connection
Absolute encoder rotary multiturn resolution / Enc abs multiturn
Absolute encoder linear measuring step resolution / Enc abs meas step
Absolute encoder rotary singleturn resolution / Enc abs singleturn
Encoder linear zero mark distance / Enc lin ZM_dist
Encoder rotary zero mark distance / Enc rot dist ZM
Encoder zero mark differential distance / Enc ZM Dif_dist
Encoder SSI baud rate / Enc SSI baud rate
Encoder SSI monoflop time / Enc SSI t_monoflop
Encoder SSI configuration / Enc SSI config
Sensor Module configuration / SM config
Angular commutation offset / Ang_com offset
Gearbox factor encoder revolutions / Grbx_fact enc_rev
Gearbox factor motor/load revolutions / Grbx_fact mot_rev
Encoder SSI error bit / Enc SSI error bit
Encoder SSI alarm bit / Enc SSI alarm bit
Encoder SSI parity bit / Enc SSI parity bit
Sensor Module configuration extended / SM config ext
Squarewave encoder filter time / Enc t_filt
Encoder ramp-up time / Enc ramp-up time
Copy encoder serial number / Copy enc ser_no
Encoder commissioning serial number part 1 / Enc comm ser_no 1
Encoder commissioning serial number part 2 / Enc comm ser_no 2
Encoder commissioning serial number part 3 / Enc comm ser_no 3
Encoder commissioning serial number part 4 / Enc comm ser_no 4
Encoder commissioning serial number part 5 / Enc comm ser_no 5
Encoder SSI number of bits before the absolute value / Enc SSI bit before
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A