Parameters For Drive Data Sets (Dds) - Siemens SINAMICS G150 Manual

2 Parameters
2.3 Parameters for data sets
p2117[0...n]
p2144[0...n]
p2148[0...n]
p2151[0...n]
p2154[0...n]
p2200[0...n]
p2220[0...n]
p2221[0...n]
p2222[0...n]
p2223[0...n]
p2235[0...n]
p2236[0...n]
p2253[0...n]
p2254[0...n]
p2264[0...n]
p2286[0...n]
p2289[0...n]
p2296[0...n]
p2297[0...n]
p2298[0...n]
p2299[0...n]
p3111[0...n]
p3112[0...n]
p3802[0...n]
2.3.2

Parameters for drive data sets (DDS)

The following list contains the parameters that are dependent on the drive data sets.
Product: SINAMICS G130/G150, Version: 4702900, Language: eng, Type: DDS
p0186[0...n]
p0187[0...n]
p0188[0...n]
p0189[0...n]
p0340[0...n]
p0572[0...n]
p0578[0...n]
p0640[0...n]
p0644[0...n]
p1001[0...n]
p1002[0...n]
p1003[0...n]
p1004[0...n]
p1005[0...n]
p1006[0...n]
p1007[0...n]
p1008[0...n]
p1009[0...n]
p1010[0...n]
p1011[0...n]
p1012[0...n]
p1013[0...n]
p1014[0...n]
p1015[0...n]
1004
BI: External alarm 3 / External alarm 3
BI: Motor stall monitoring enable (negated) / Mot stall enab neg
BI: RFG active / RFG active
CI: Speed setpoint for messages/signals / n_set for msg
CI: Speed setpoint 2 / n_set 2
BI: Technology controller enable / Tec_ctrl enable
BI: Technology controller fixed value selection bit 0 / Tec_ctrl sel bit 0
BI: Technology controller fixed value selection bit 1 / Tec_ctrl sel bit 1
BI: Technology controller fixed value selection bit 2 / Tec_ctrl sel bit 2
BI: Technology controller fixed value selection bit 3 / Tec_ctrl sel bit 3
BI: Technology controller motorized potentiometer raise setpoint / Tec_ctrl mop raise
BI: Technology controller motorized potentiometer lower setpoint / Tec_ctrl mop lower
CI: Technology controller setpoint 1 / Tec_ctrl setp 1
CI: Technology controller setpoint 2 / Tec_ctrl setp 2
CI: Technology controller actual value / Tec_ctrl act val
BI: Hold technology controller integrator / Tec_ctr integ hold
CI: Technology controller pre-control signal / Tec_ctr prectr_sig
CI: Technology controller output scaling / Tec_ctrl outp scal
CI: Technology controller maximum limit signal source / Tec_ctrMaxLimS_src
CI: Technology controller minimum limit signal source / Tec_ctrl min_l s_s
CI: Technology controller limit offset / Tech_ctrl lim offs
BI: External fault 3 enable / Ext fault 3 enab
BI: External fault 3 enable negated / Ext flt 3 enab neg
BI: Sync-line-drive enable / Sync enable
Motor Data Sets (MDS) number / MDS number
Encoder 1 encoder data set number / Enc 1 EDS number
Encoder 2 encoder data set number / Enc 2 EDS number
Encoder 3 encoder data set number / Enc 3 EDS number
Automatic calculation motor/control parameters / Calc auto par
Activate/de-activate inhibit list / Inh_list act/deact
Calculate technology-dependent parameters / Calc tec par
Current limit / Current limit
Current limit excitation induction motor / Imax excitat ASM
CO: Fixed speed setpoint 1 / n_set_fixed 1
CO: Fixed speed setpoint 2 / n_set_fixed 2
CO: Fixed speed setpoint 3 / n_set_fixed 3
CO: Fixed speed setpoint 4 / n_set_fixed 4
CO: Fixed speed setpoint 5 / n_set_fixed 5
CO: Fixed speed setpoint 6 / n_set_fixed 6
CO: Fixed speed setpoint 7 / n_set_fixed 7
CO: Fixed speed setpoint 8 / n_set_fixed 8
CO: Fixed speed setpoint 9 / n_set_fixed 9
CO: Fixed speed setpoint 10 / n_set_fixed 10
CO: Fixed speed setpoint 11 / n_set_fixed 11
CO: Fixed speed setpoint 12 / n_set_fixed 12
CO: Fixed speed setpoint 13 / n_set_fixed 13
CO: Fixed speed setpoint 14 / n_set_fixed 14
CO: Fixed speed setpoint 15 / n_set_fixed 15
SINAMICS G130/G150
List Manual (LH2), 04/2014, A5E03263479A